series synchronous cylinder Sold to Cameroon

This article mainly introduces:

Cameroon hydraulic cylinder,series synchronous cylinder manufacturer,series synchronous cylinder

(Cameroon series synchronous cylinder,produced by Hengyu Hydraulic Cylinder Factory）

series synchronous cylinder are widely used in Cameroon，because of excellent fatigue and impact resistance，no need for deceleration device，long service life.So our company has designed series synchronous cylinder for customers from Cameroon.

Introduction to series synchronous cylinder:

The internal leakage of the series synchronous cylinder should be prevented when the series synchronous cylinder is used. The internal leakage of series synchronous cylinder includes the leakage caused by excessive wear of series synchronous cylinder block seal, piston rod and seal cover seal and piston seal. The cause of sealing leakage between the piston rod and the seal cover is that the seal is wrinkled, squeezed, torn, worn, aging, deterioration, deformation, etc., and a new seal should be replaced at this time.

When the series synchronous cylinder is in use, measures should be added to prevent the intrusion of pollutants. Effective measures should be taken to control the intrusion of pollutants, such as installing high-efficiency air filters in the tank breathing holes, new oil must be filtered, etc., but also must improve the anti-pollution ability of the series synchronous cylinder itself. In the seriously polluted environment, it is more important to pay attention to, such as the underground oil series synchronous cylinder should use fluorine rubber (FRM) and nitrile rubber (NBR) dust ring, and the ground mechanical series synchronous cylinder should use nitrile rubber dust ring; The filter device is added to the oil inlet of the series synchronous cylinder of the dump truck, construction machinery, work platform and other equipment, and in order to reduce the oil inlet resistance, the flow area should be increased as much as possible, which can effectively reduce the particle pollution from the system.

The difference between the integral series synchronous cylinder and the split series synchronous cylinder: The integral series synchronous cylinder and the split series synchronous cylinder in the series synchronous cylinder are two different series synchronous cylinders, and they are very different. The whole series synchronous cylinder, which is cast in one body, is not prone to problems such as oil leakage; The split series synchronous cylinder is welded twice, so if it is not handled well at the welding, it is prone to problems such as oil leakage and series synchronous cylinder damage. Therefore, it is obvious that the answer to this question is for difference.

At the rated pressure, the thrust of the series synchronous cylinder is determined by what factors: at the rated pressure of the oil pump, the work done by the series synchronous cylinder is related to the diameter of the series synchronous cylinder, but not to the stroke of the series synchronous cylinder. Moreover, the larger the series synchronous cylinder diameter, the larger the area, and the greater the pressure obtained. To this point, we should have a correct understanding and clear understanding, so as to avoid problems in the use of the series synchronous cylinder.

Answers to some questions about series synchronous cylinder:

Structural characteristics of the plunger cylinder? (1) The plunger hydraulic cylinder is a single-acting hydraulic cylinder, which can only move in one direction by hydraulic pressure, and the return trip of the plunger depends on other external forces or the weight of the plunger; (2) The plunger is only supported by the cylinder liner and is not in contact with the cylinder liner, so the cylinder liner is easy to process, so it is suitable for long stroke hydraulic cylinder; (3) the total pressure of the plunger during work, so it must have sufficient stiffness; (4) The weight of the plunger is often large, and it is easy to sag due to its own weight when placed horizontally, resulting in wear of the seals and guide side, so its vertical use is more favorable.

How to remove the cylinder correctly?
(1) Before disassembling the hydraulic cylinder, the hydraulic circuit should be depressurized. Otherwise, when the tubing joint connected with the cylinder is loosened, the high-pressure oil in the circuit will be quickly ejected. The hydraulic circuit of the hydraulic press should first loosen the hand wheel or pressure regulator screw at the relief valve, so that the pressure oil is unloaded, and then block the power supply or block the power source to stop the operation of the hydraulic equipment. (2) When disassembling, it should prevent damage to the top thread of the piston rod, the oil thread, the appearance of the piston rod, the inner wall of the cylinder liner, etc. In order to prevent the piston rod and other slender parts from twisting or deformation, the use of cushion wood support balance when placed. (3) Disassemble in order.