yg series hydraulic cylinder Sold to Egypt

This article mainly introduces:

Egypt hydraulic cylinder,yg series hydraulic cylinder manufacturer,yg series hydraulic cylinder

(Egypt yg series hydraulic cylinder,produced by Hengyu Group）

yg series hydraulic cylinder are widely used in Egypt，because of excellent temperature resistance，no transmission clearance，powerful torque.So our company has designed yg series hydraulic cylinder for customers from Egypt.

Introduction to yg series hydraulic cylinder:

Do not regularly check the damage of the chrome layer of the yg series hydraulic cylinder: completely extend the yg series hydraulic cylinder and carefully check whether there is any surface damage such as injury, strain, welding slag, such as the surface damage position, in the yg series hydraulic cylinder block < 20cm, and the damage depth < 5mm, should be repaired in time to prevent long-term damage to the yg series hydraulic cylinder seal. Welding slag is strictly prohibited on the surface of the yg series hydraulic cylinder.

When the yg series hydraulic cylinder thrust is insufficient, check the hydraulic circuit for leaks. Including leakage of valves and hydraulic lines. The inspection method is to check and eliminate the leakage of the hydraulic connection line by manipulating the reversing valve. Also consider the relief valve. If the relief valve enters the dirt and jams the spool, so that the relief valve is normally open, the hydraulic oil will flow directly back to the tank through the relief valve bypass, resulting in no oil in the yg series hydraulic cylinder. If the load is too large, although the regulating pressure of the relief valve has reached the maximum rating, the yg series hydraulic cylinder still cannot get the thrust required for continuous action without action. If the regulating pressure is low, the pressure is insufficient to achieve the required vertebra force, which is manifested as insufficient thrust. Check and adjust the relief valve at this time.

The difference between the plunger yg series hydraulic cylinder and the piston yg series hydraulic cylinder is that the piston in the yg series hydraulic cylinder is replaced by a shaft plunger, which is used in hydraulic transmission requiring a long mechanical stroke, and can only input pressure oil from one direction, pressurize in a single direction, and form a thrust to push the plunger to move. The return trip of the plunger depends on the plunger itself to fall, and some rely on the spring to push back to the original position. Usually used plunger type yg series hydraulic cylinder, its inner hole does not need mechanical finishing, as long as the plunger round grinding can be assembled.

What kind of process is used in the yg series hydraulic cylinder to make high-quality yg series hydraulic cylinder products: the body is the main component of the yg series hydraulic cylinder, mining single pillar, hydraulic support, gun tube and other products, and its processing quality directly affects the life and reliability of the entire product. Body processing requirements are high, the internal surface roughness requirements are Ra0.4 ~ 0.8&um, the coaxiality, wear resistance requirements are strict. The basic feature of body is deep hole processing, which has always troubled the processing personnel. The yg series hydraulic cylinder products of our company mainly use rolling processing, because the surface layer has surface residual compressive stress, which helps to close the surface micro-cracks and hinder the expansion of erosion. Thus, the corrosion resistance of the surface can be improved, and the fatigue crack can be delayed or expanded, and the fatigue strength of the body can be improved. The correct rolling process of the yg series hydraulic cylinder block: broaching block - fine boring block - grinding block. The rolling method is: broaching block - fine boring block - rolling block, the process is 3 parts, but the time is compared: grinding 1 meter of the block is about 1-2 days, rolling 1 meter of the block is about 10-30 minutes. Input comparison: grinding machine or quilting machine (tens of thousands - millions), rolling knife (ten thousand - tens of thousands). After rolling, the surface roughness of the hole decreases from RA3.2-6.3um before rolling to RA0.4-0.8&um, the surface hardness of the hole increases by about 30%, and the fatigue strength of the inner surface of the yg series hydraulic cylinder increases by 25%. If the service life of the yg series hydraulic cylinder is only considered, it is increased by 2 to 3 times, and the efficiency of the boring and rolling process is about 3 times higher than that of the grinding process. yg series hydraulic cylinder misoperation or operation failure may be caused by the following reasons, you can start from these aspects of the investigation: (1) spool stuck or valve hole blocked. When the spool of the flow valve or direction valve is stuck or the valve hole is blocked, the yg series hydraulic cylinder is prone to misoperation or operation failure. At this time, the contamination of the oil should be checked; Check whether dirt or colloidal deposits are stuck in the spool or blocking the valve hole; Check the wear of the valve body, clean and replace the system filter, clean the fuel tank, and replace the hydraulic medium. (2) The piston rod and yg series hydraulic cylinder are stuck or the yg series hydraulic cylinder is blocked. At this time, no matter how to manipulate, the yg series hydraulic cylinder does not move or moves very little. At this time, check whether the piston and piston rod seal is too tight, whether it enters the dirt and gum deposits: whether the shaft line of the piston rod and the yg series hydraulic cylinder is in the center, whether the wearing parts and seals are invalid, and whether the load is too large.

Answers to some questions about yg series hydraulic cylinder:

How to calculate the hydraulic cylinder pressure, how much pressure can put up how much weight?
There is a formula for air pressure, hydraulic pressure, water pressure: F=P×S type: f-cylinder or hydraulic cylinder output, unit is Newton (N) P- pressure, unit is Mpa S- effective area, unit is square millimeter (mm2), note: is the effective area, in the hydraulic cylinder to subtract the cross-sectional area of the piston rod.

How to design the guide sleeve of cylinder diameter 400?
The purpose of the guide sleeve is to guide and seal. Therefore, it is necessary to look at the speed of the piston rod, working pressure and radial force. High speed, medium pressure, no (or very little) radial force, with a Steseal. Low speed and heavy load, medium radial force, combined seal. High speed and heavy load, large radial force, sealed with DU sleeve + copper ring + combination. The combination seal must have a lubricating oil passage, and a seal must be added to the outside of the oil passage.