cargo elevator hydraulic cylinder Sold to Italy

This article mainly introduces:

Italy hydraulic cylinder,cargo elevator hydraulic cylinder manufacturer,cargo elevator hydraulic cylinder

(Italy cargo elevator hydraulic cylinder,produced by Hengyu Group）

cargo elevator hydraulic cylinder are widely used in Italy，because of clever hydraulic energy conversion，simple structure and reliable operation，excellent temperature resistance.So our company has designed cargo elevator hydraulic cylinder for customers from Italy.

Introduction to cargo elevator hydraulic cylinder:

Analysis of commonly used seals: The wear ring and slip ring commonly used on the cargo elevator hydraulic cylinder are generally made of polytetrafluoroethylene + graphite, because pure polytetrafluoroethylene is easy to produce plastic creep, which is only suitable for low pressure and low wear resistance conditions. If the sealing ring used is a composite material formed after adding graphite filler, the performance can be effectively improved, the ability to resist plastic creep is increased by 2 to 3 times, the initial deformation caused by the load is reduced by 30 to 60% : the rigidity is increased by 2 to 3 times: the dimensional stability under heat is increased by 2 times, and the hardness is increased by l0 to 15%.

cargo elevator hydraulic cylinder buffer valve inspection and maintenance: For the valve buffer cargo elevator hydraulic cylinder, the focus should be on checking the wear of the buffer valve spool and seat. Once it is found that the amount of wear increases and the seal fails, it should be replaced. It can also be repaired by using abrasive spool and seat matching grinding method.

If the cargo elevator hydraulic cylinder slips or crawls, please check whether there is astringency inside the cargo elevator hydraulic cylinder, because the internal parts of the cargo elevator hydraulic cylinder are improperly assembled, the parts are deformed, worn or the shape and position tolerance is excessive, the action resistance is too large, so that the piston speed of the cargo elevator hydraulic cylinder changes with the different stroke position, and the slip or crawl occurs. Most of the reasons are due to poor assembly quality of parts, surface scars or sintered iron filings, so that the resistance increases, the speed decreases. For example, the piston is different from the piston rod or the piston rod is bent, the cargo elevator hydraulic cylinder or the piston rod is offset from the mounting position of the guide rail, and the sealing ring is too tight or too loose. The solution is to repair or adjust, replace damaged parts and remove iron filings.

What kind of process is used in the cargo elevator hydraulic cylinder to make high-quality cargo elevator hydraulic cylinder products: the body is the main component of the cargo elevator hydraulic cylinder, mining single pillar, hydraulic support, gun tube and other products, and its processing quality directly affects the life and reliability of the entire product. Body processing requirements are high, the internal surface roughness requirements are Ra0.4 ~ 0.8&um, the coaxiality, wear resistance requirements are strict. The basic feature of body is deep hole processing, which has always troubled the processing personnel. The cargo elevator hydraulic cylinder products of our company mainly use rolling processing, because the surface layer has surface residual compressive stress, which helps to close the surface micro-cracks and hinder the expansion of erosion. Thus, the corrosion resistance of the surface can be improved, and the fatigue crack can be delayed or expanded, and the fatigue strength of the body can be improved. The correct rolling process of the cargo elevator hydraulic cylinder block: broaching block - fine boring block - grinding block. The rolling method is: broaching block - fine boring block - rolling block, the process is 3 parts, but the time is compared: grinding 1 meter of the block is about 1-2 days, rolling 1 meter of the block is about 10-30 minutes. Input comparison: grinding machine or quilting machine (tens of thousands - millions), rolling knife (ten thousand - tens of thousands). After rolling, the surface roughness of the hole decreases from RA3.2-6.3um before rolling to RA0.4-0.8&um, the surface hardness of the hole increases by about 30%, and the fatigue strength of the inner surface of the cargo elevator hydraulic cylinder increases by 25%. If the service life of the cargo elevator hydraulic cylinder is only considered, it is increased by 2 to 3 times, and the efficiency of the boring and rolling process is about 3 times higher than that of the grinding process. cargo elevator hydraulic cylinder misoperation or operation failure may be caused by the following reasons, you can start from these aspects of the investigation: (1) spool stuck or valve hole blocked. When the spool of the flow valve or direction valve is stuck or the valve hole is blocked, the cargo elevator hydraulic cylinder is prone to misoperation or operation failure. At this time, the contamination of the oil should be checked; Check whether dirt or colloidal deposits are stuck in the spool or blocking the valve hole; Check the wear of the valve body, clean and replace the system filter, clean the fuel tank, and replace the hydraulic medium. (2) The piston rod and cargo elevator hydraulic cylinder are stuck or the cargo elevator hydraulic cylinder is blocked. At this time, no matter how to manipulate, the cargo elevator hydraulic cylinder does not move or moves very little. At this time, check whether the piston and piston rod seal is too tight, whether it enters the dirt and gum deposits: whether the shaft line of the piston rod and the cargo elevator hydraulic cylinder is in the center, whether the wearing parts and seals are invalid, and whether the load is too large.

Answers to some questions about cargo elevator hydraulic cylinder:

How to repair if hydraulic shears cylinder oil leakage?
The hydraulic cylinder is generally disassembled and the sealing ring is replaced. There are generally two ways to install the ends of the hydraulic cylinder. The larger hydraulic cylinder is mostly flanged disc type, which is screwed to the middle cylinder block by several bolts, the bolts are removed, and the cylinder head is slowly pulled out. The smaller hydraulic cylinder, the cylinder block and the head itself are threaded, and the rotating end cap can be removed from the cylinder block. If you do not understand the hydraulic cylinder, it is best to ask someone to deal with it. It is easy to damage the sealing ring and internal surface during disassembly.

The pressure gauge of the hydraulic station reaches 20MPa. How many tons of weight can the hydraulic cylinder lift? How to convert?
20Mpa=200kg/cm^2 The weight of the cylinder with a cross-sectional area of 1 square centimeter can be lifted is 200kg, so F=200X3.14X (125/2) ^2 =24531kg =24.5 tons.