stroke adjustable cylinder Sold to Ireland

This article mainly introduces:

Ireland hydraulic cylinder,stroke adjustable cylinder manufacturer,stroke adjustable cylinder

(Ireland stroke adjustable cylinder,produced by Hengyu Group）

stroke adjustable cylinder are widely used in Ireland，because of long service life，excellent fatigue and impact resistance，no need for deceleration device.So our company has designed stroke adjustable cylinder for customers from Ireland.

Introduction to stroke adjustable cylinder:

The wear of the hard chromium plating layer of the stroke adjustable cylinder is mostly caused by the grinding of the friction iron powder of the piston, and the wear is faster when there is water in the middle. Corrosion caused by the contact potential difference of the metal only occurs in the part of the piston contact, and the corrosion occurs in a point pattern. As mentioned above, when there is moisture in the middle, it will promote the development of corrosion. Compared with castings, the contact potential difference of copper alloy is higher, so the corrosion degree of copper alloy is more serious.

When the stroke adjustable cylinder wear is serious, you can try to use an alloy scraper to shave grooves with a depth of more than 1mm on the surface of the slip injury, then clean the grooves with acetone, apply the adjusted TS311 anti-wear repair agent on the polished surface with the stroke adjustable cylinder inner diameter copying plate, and scrape it flat vigorously to ensure compaction and higher than the inner surface of the stroke adjustable cylinder. After curing, polish to leave a finishing margin. Finally, the overall size, shape tolerance and roughness of the stroke adjustable cylinder can meet the requirements by grinding. However, the life and reliability of this repair stroke adjustable cylinder are not high.

When the stroke adjustable cylinder is in use, measures should be added to prevent the intrusion of pollutants. Effective measures should be taken to control the intrusion of pollutants, such as installing high-efficiency air filters in the tank breathing holes, new oil must be filtered, etc., but also must improve the anti-pollution ability of the stroke adjustable cylinder itself. In the seriously polluted environment, it is more important to pay attention to, such as the underground oil stroke adjustable cylinder should use fluorine rubber (FRM) and nitrile rubber (NBR) dust ring, and the ground mechanical stroke adjustable cylinder should use nitrile rubber dust ring; The filter device is added to the oil inlet of the stroke adjustable cylinder of the dump truck, construction machinery, work platform and other equipment, and in order to reduce the oil inlet resistance, the flow area should be increased as much as possible, which can effectively reduce the particle pollution from the system.

Regular maintenance of the stroke adjustable cylinder includes: regular tightening, stroke adjustable cylinder fastening screws and gland screws, stroke adjustable cylinder piston rod stop adjustment screws, should be tightened once a month, tighten each screw evenly, and achieve the corresponding tightening torque. Replace the seal regularly, it is recommended to replace the seal of the stroke adjustable cylinder once a year. Clean regularly, the stroke adjustable cylinder is cleaned every other year, and the seals are replaced while cleaning.

Answers to some questions about stroke adjustable cylinder:

Is the hydraulic cylinder leaking because there is no pressure?
HC hydraulic cylinder common leakage reasons, first: most of the reasons are because the seal surface wear or aging leads to poor sealing, so there is no pressure to operate, as long as the piston seal can be replaced. Second: It may also be the piston rod strain, repair the piston rod is good. If it is because the piston strength is not enough and the playing time is long, it is necessary to replace the piston.

How does the clamping cylinder work?
Hydraulic transmission principle: oil as the working medium, through the change of the sealing volume to transfer movement, through the internal pressure of the oil to transfer power. 1. The power part - converts the mechanical energy of the prime mover into the pressure energy of the oil (hydraulic energy). For example: hydraulic pump. 2, The executive part - the hydraulic pump input oil pressure energy into the mechanical energy to drive the working mechanism. For example: hydraulic cylinder, hydraulic motor. 3, The control part - used to control and adjust the oil pressure, flow and flow direction. For example: pressure control valve, flow control valve and direction control valve. 4, The auxiliary part - the first three parts are connected together to form a system, which plays the role of oil storage, filtration, measurement and sealing.