supporting cylinder Sold to Bolivia

This article mainly introduces:

Bolivia hydraulic cylinder,supporting cylinder manufacturer,supporting cylinder

(Bolivia supporting cylinder,produced by Hengyu Hydraulic Cylinder Factory）

supporting cylinder are widely used in Bolivia，because of long service life，smooth movement，high work efficiency.So our company has designed supporting cylinder for customers from Bolivia.

Introduction to supporting cylinder:

The coordination of the sliding parts of the supporting cylinder itself should not be too tight, the sealing friction force should not be too large, and H8 / f8 coordination should be selected between the piston rod and the guide sleeve; Check whether the size of the sealing ring is processed strictly according to the standard; If the V-shaped sealing ring is used, the sealing friction should be adjusted to a moderate degree.

The supporting cylinder pipe should not be left behind when deburring at both ends after the fixed length processing. In addition, the placement of steel pipes near the site of welding pipeline operations is the cause of welding foreign objects. The pipes placed near the welding operation site should be sealed. It must also be noted that pipe fitting materials should be fully prepared on a dust-free workbench.

When the supporting cylinder is installed, the piston and the supporting cylinder head and other parts have large mass, large size and large inertia, even if there is a lifting equipment auxiliary installation, because the specified clearance is small, no matter how hard it will be put into, therefore, the end of the piston or the supporting cylinder head boss is easy to cause scars when it hits the inner surface of the supporting cylinder wall. The solution to this problem: for a large number of small products, the use of autocratic assembly oriented tools during installation; For heavy, thick and large large and medium-sized supporting cylinders, only careful and careful operation can be avoided.

If the supporting cylinder operation failure, you can start from these aspects to troubleshoot: (1) the hydraulic system control pressure is too low. The throttling resistance in the control line may be too large, the flow valve is improperly adjusted, the control pressure is inappropriate, and the pressure source is disturbed. At this time, the control pressure source should be checked to ensure that the pressure is adjusted to the specified value of the system; (2) Air enters the hydraulic system. Mainly because there is a leak in the system. At this time, check the liquid level of the hydraulic tank, the seals and fittings on the oil suction side of the hydraulic pump, and whether the oil suction filter is too dirty. If so, the hydraulic oil should be replenished, seals and fittings should be treated, and the coarse filter element should be cleaned or replaced. (3) The initial action of the supporting cylinder is slow. In the case of low temperature, the hydraulic oil viscosity is large, poor flow, resulting in slow supporting cylinder action. The improvement method is to replace the hydraulic oil with better viscosity and temperature performance If the supporting cylinder is weak and cannot push the load, please check the internal leakage problem. The internal leakage of the supporting cylinder includes the leakage caused by excessive wear of the supporting cylinder block seal, the piston rod and the seal cover seal and the piston seal. The cause of sealing leakage between the piston rod and the seal cover is that the seal is wrinkled, squeezed, torn, worn, aging, deterioration, deformation, etc., and a new seal should be replaced at this time. The main cause of excessive piston seal wear is improper adjustment of the speed control valve, resulting in excessive back pressure and improper seal installation or hydraulic oil contamination. The second is that foreign bodies enter the assembly and the quality of sealing materials is not good. The result is that the action is slow and weak, and in serious cases, it will cause damage to the piston and supporting cylinder, and the phenomenon of "pulling the supporting cylinder" appears. The treatment method is to adjust the speed control valve, and the necessary operations should be done according to the installation instructions.

Answers to some questions about supporting cylinder:

Is there a national standard for the testing of hydraulic cylinders?
Generally speaking, the cylinder test is carried out according to JB/JQ20302 Allowable leakage of cylinder in pre-factory leakage test. GB2879 hydraulic cylinder piston and piston rod dynamic seal groove type, size and tolerance. GB6578 hydraulic cylinder piston rod dust ring groove type, size and tolerance. GB7938 hydraulic cylinder and cylinder nominal pressure series, etc.

Why do two hydraulic cylinders lift out of sync?
There may be several situations (do not know the result of the equipment, may not be accurate) 1, whether the slow one is worn 2, whether there is air in the slow cylinder 3, if the two cylinders are supplied by the same oil port, whether the slow joint is blocked (some processing residue will reach a certain oil port under a certain coincidence condition, This situation will not happen if it is not necessarily good before) 4, the oil seal in the slow cylinder leaks, causing the feed oil to leak from the return oil end. Point 4 is most likely because it is invisible and a technical failure. If it is a dual oil feed (separate oil feed), it is also necessary to check the oil supply system and the oil return system (valve type).