yg series hydraulic cylinder Sold to Colombia

This article mainly introduces:

Colombia hydraulic cylinder,yg series hydraulic cylinder manufacturer,yg series hydraulic cylinder

(Colombia yg series hydraulic cylinder,produced by Hengyu Hydraulic Co., Ltd）

yg series hydraulic cylinder are widely used in Colombia，because of high work efficiency，excellent fatigue and impact resistance，no need for deceleration device.So our company has designed yg series hydraulic cylinder for customers from Colombia.

Introduction to yg series hydraulic cylinder:

yg series hydraulic cylinder buffer valve inspection and maintenance: For the valve buffer yg series hydraulic cylinder, the focus should be on checking the wear of the buffer valve spool and seat. Once it is found that the amount of wear increases and the seal fails, it should be replaced. It can also be repaired by using abrasive spool and seat matching grinding method.

The quality of the yg series hydraulic cylinder can not be ignored in the purchase of the yg series hydraulic cylinder. The yg series hydraulic cylinder is the main component of the yg series hydraulic cylinder, the single pillar for mining, the hydraulic support, the gun tube and other products, and its processing quality directly affects the life and reliability of the entire product. yg series hydraulic cylinder processing requirements are high, its internal surface roughness requirements are Ra0.4 ~ 0.8μm, the coaxiality, wear resistance requirements are strict. The basic feature of yg series hydraulic cylinder is deep hole processing, which has always troubled the processing personnel.

The difference between the integral yg series hydraulic cylinder and the split yg series hydraulic cylinder: The integral yg series hydraulic cylinder and the split yg series hydraulic cylinder in the yg series hydraulic cylinder are two different yg series hydraulic cylinders, and they are very different. The whole yg series hydraulic cylinder, which is cast in one body, is not prone to problems such as oil leakage; The split yg series hydraulic cylinder is welded twice, so if it is not handled well at the welding, it is prone to problems such as oil leakage and yg series hydraulic cylinder damage. Therefore, it is obvious that the answer to this question is for difference.

Most of the failure of the yg series hydraulic cylinder is because there is a foreign body in the yg series hydraulic cylinder into the failure of the yg series hydraulic cylinder, the most problematic is that it is difficult to determine when the foreign body is into the yg series hydraulic cylinder. After a foreign body enters, if the outer side of the sliding surface of the piston is equipped with a seal with a lip edge, then the lip edge of the seal can scrape the foreign body when working, which is beneficial to avoid scratching. However, the piston equipped with 0-shaped sealing ring has a sliding surface at both ends, and foreign bodies are sandwiched between this sliding surface, which is easy to form scars.

Answers to some questions about yg series hydraulic cylinder:

Injection molding machine die thimble on the side of the feed nozzle, the oil cylinder pull the thimble shift, how to debug the oil cylinder?
The cylinder is connected with the neutron of the injection molding machine, the neutron is retreated after the opening mold is in place, the cylinder taps the thimble plate to the top, and then takes, and the neutron is reset.

Can a leak in the cylinder cause the hydraulic system to fail?
Leakage in the cylinder can cause the hydraulic system to fail. Cylinder leakage (internal leakage) first affects the controlled action of the hydraulic system can not meet the requirements (such as the movement speed of the cylinder, the insufficient thrust and tension of the cylinder), if the internal leakage of the cylinder is too large, it may also cause the cylinder to be unable to promote the load movement. Second, the existence of internal leakage (internal leakage) of the oil cylinder will lead to the rapid rise (or too high) of the oil temperature of the hydraulic system, and the high oil temperature will not only waste the energy conversion of the system, but also lead to the reduction of the viscosity of the oil, which will accelerate the aging and destruction of the seals such as pumps, valves, cylinders, pipelines, and at the same time, the lubrication effect of the hydraulic oil is reduced, and the production of iron filings that increase the friction of the hydraulic system.