synchronous hydraulic cylinder Sold to Nigeria

This article mainly introduces:

Nigeria hydraulic cylinder,synchronous hydraulic cylinder manufacturer,synchronous hydraulic cylinder

(Nigeria synchronous hydraulic cylinder,produced by Hengyu Hydraulic Co., Ltd）

synchronous hydraulic cylinder are widely used in Nigeria，because of no transmission clearance，simple structure and reliable operation，excellent temperature resistance.So our company has designed synchronous hydraulic cylinder for customers from Nigeria.

Introduction to synchronous hydraulic cylinder:

Regular maintenance of the synchronous hydraulic cylinder includes: regular tightening, synchronous hydraulic cylinder fastening screws and gland screws, synchronous hydraulic cylinder piston rod stop adjustment screws, should be tightened once a month, tighten each screw evenly, and achieve the corresponding tightening torque. Replace the seal regularly, it is recommended to replace the seal of the synchronous hydraulic cylinder once a year. Clean regularly, the synchronous hydraulic cylinder is cleaned every other year, and the seals are replaced while cleaning.

Piston synchronous hydraulic cylinder is widely used in hydraulic transmission. When the synchronous hydraulic cylinder works, it mainly delivers hydraulic oil alternately to both sides of the piston in the synchronous hydraulic cylinder, and uses the pressure difference of hydraulic oil on both sides of the piston to realize the reciprocating movement of the piston. If you want to speed up the forward speed of the piston, the return oil in the synchronous hydraulic cylinder can be controlled by the valve and directly input into the inlet pipe to participate in the work of the piston to achieve rapid movement of the piston, but the thrust of the piston is reduced much.

Improve the service life of the synchronous hydraulic cylinder: it is necessary to maintain the normal clearance of the combined surface of the hydraulic components. When manufacturing or repairing the main parts of the synchronous hydraulic cylinder (such as the synchronous hydraulic cylinder block, piston rod, etc.), the assembly should be carried out in accordance with the tolerance lower limit of the assembly size, which can well reduce the occurrence of cavitation. If cavitation has occurred in the hydraulic components, only metallographic sandpaper polishing technology can be used to remove cavitation pitting and surface carbon deposits, and general fine sandpaper must not be used for polishing After the synchronous hydraulic cylinder is repaired, the hydraulic system should run smoothly for a certain period of time so that the hydraulic oil in the hydraulic system can be fully circulated; If necessary, the synchronous hydraulic cylinder inlet pipe (or return pipe) can be disassembled. Make the hydraulic oil overflow to achieve the effect of single synchronous hydraulic cylinder exhaust.

When the long-stroke synchronous hydraulic cylinder rotates horizontally, the piston rod bends due to its own weight, causing the guide sleeve and piston to produce biased load, resulting in synchronous hydraulic cylinder head seal damage, oil leakage, and piston sleep in the synchronous hydraulic cylinder. The following measures can be taken: increase the piston plan to adjust the piston outer circle and process it into a convex drum, so that the piston can self-position, improve the force situation, and reduce and avoid pulling the synchronous hydraulic cylinder; The piston and the piston rod are connected with a spherical joint.

Answers to some questions about synchronous hydraulic cylinder:

Why does the hydraulic cylinder not return?
For a spring return cylinder, it is possible that 1, the spring is damaged. You can check it for processing. 2, the oil in the oil path is not unloaded, causing it to be unable to reset. 3, the cylinder piston is dead, resulting in no position. For double-acting cylinders, it is possible to: 1, the spool is not reversed, or is not changed to the correct position, check whether the reversing valve is normal (and whether there is electricity). 2, the cylinder piston is dead, resulting in no position, check and treatment can be. 3, the return oil pressure is insufficient, the inlet oil is not unloaded, the operation is not smooth. For reference only.

How to disassemble the big nut that excavate the oil cylinder piston of the excavator?
If you want to be safe, look for a special unloading place for this thing, which is an oil cylinder on top of a turntable with a large nut attached to the center of the turntable. If you're in the field just pin the head of the cylinder to one end, use a big homemade wrench to hold the nut in place, and then get a digging machine and push it down, and it opens.