road paving machine hydraulic cylinder Sold to Switzerland

This article mainly introduces:

Switzerland hydraulic cylinder,road paving machine hydraulic cylinder manufacturer,road paving machine hydraulic cylinder

(Switzerland road paving machine hydraulic cylinder,produced by Hengyu Hydraulic Cylinder Factory）

road paving machine hydraulic cylinder are widely used in Switzerland，because of excellent fatigue and impact resistance，no need for deceleration device，long service life.So our company has designed road paving machine hydraulic cylinder for customers from Switzerland.

Introduction to road paving machine hydraulic cylinder:

The assembly work of the road paving machine hydraulic cylinder has a great impact on the quality of the road paving machine hydraulic cylinder: each part must be carefully cleaned before assembly; To correctly install the sealing device everywhere: when installing the sealing ring, pay attention to its installation direction to avoid oil leakage due to installation, and its lip should be equipped with a pressure oil chamber. In addition, because it is a YX-shaped sealing ring, it is necessary to pay attention to distinguish between shaft and hole use, do not install wrong; Because the sealing device is matched with the sliding surface, an appropriate amount of hydraulic oil should be applied during assembly; The special wrench should be used when the threaded coupling is tightened, and the torque should meet the standard requirements; After the piston and piston rod are assembled, it is necessary to measure whether the coaxiality and straightness on the full length are out of whack. After assembly, there should be no blocking sensation and uneven resistance when the piston assembly moves.

The difference between the plunger road paving machine hydraulic cylinder and the piston road paving machine hydraulic cylinder is that the piston in the road paving machine hydraulic cylinder is replaced by a shaft plunger, which is used in hydraulic transmission requiring a long mechanical stroke, and can only input pressure oil from one direction, pressurize in a single direction, and form a thrust to push the plunger to move. The return trip of the plunger depends on the plunger itself to fall, and some rely on the spring to push back to the original position. Usually used plunger type road paving machine hydraulic cylinder, its inner hole does not need mechanical finishing, as long as the plunger round grinding can be assembled.

When the road paving machine hydraulic cylinder is customized, if there are high requirements for the quality of the road paving machine hydraulic cylinder, it is best to use rolling processing, because the surface layer has surface residual compressive stress, which helps to close the surface of the small crack, preventing the expansion of erosion. Thus, the corrosion resistance of the surface can be improved, and the fatigue crack can be delayed or expanded, and the fatigue strength of the road paving machine hydraulic cylinder can be improved. By rolling forming, a cold working hardening layer is formed on the rolling surface, which reduces the elastic and plastic deformation of the contact surface of the grinding pair, thereby improving the wear resistance of the inner wall of the road paving machine hydraulic cylinder and avoiding the burn caused by grinding. After rolling, the reduction of surface roughness value can improve the matching property.

road paving machine hydraulic cylinders in series, parallel and series parallel. Series: In the road paving machine hydraulic cylinder, the oil inlet of the subsequent reversing valve is the supply of the previous oil return, and there is no separate oil return circuit connected with the oil return in each valve. Series: In the road paving machine hydraulic cylinder, the oil inlet of the subsequent reversing valve is the supply of the previous oil return, and there is no separate oil return circuit connected with the oil return in each valve. Parallel: the pressure oil in the road paving machine hydraulic cylinder is connected with the inlet oil of each reversing valve, and the return oil is collected by the return oil circuit. Series parallel: For this one, compared with the simple series and parallel, it is slightly more complicated, but it is not impossible to understand. The series refers to the oil in the road paving machine hydraulic cylinder, which is in series form, but can not form a series circuit, and the parallel refers to the oil return circuit of each valve, which is in parallel.

Answers to some questions about road paving machine hydraulic cylinder:

What is a two-way hydraulic cylinder?
Bidirectional hydraulic cylinder definition: The bidirectional hydraulic cylinder uses the oil as the working medium, transmits the movement through the change of the sealing volume, and transmits the power through the pressure inside the oil. The two-way cylinder has at least two oil ports, which are used to connect the hydraulic tubing, and control the extension and retraction of the cylinder by pressing.

What is the reason why the hydraulic cylinder is not good at lifting?
There may be several situations 1, whether the slow one is worn 2, whether there is air in the slow cylinder 3, if the two cylinders are supplied by the same oil port, whether the slow joint is blocked (some processing residue will reach a certain oil port under a certain coincidence condition, This situation will not happen if it is not necessarily good before) 4, the oil seal in the slow cylinder leaks, causing the feed oil to leak from the return oil end. Point 4 is most likely because it is invisible and a technical failure. If it is a dual oil feed (separate oil feed), it is also necessary to check the oil supply system and the oil return system (valve type).