supporting cylinder Sold to Hungary

This article mainly introduces:

Hungary hydraulic cylinder,supporting cylinder manufacturer,supporting cylinder

(Hungary supporting cylinder,produced by Hengyu Hydraulic Cylinder Factory）

supporting cylinder are widely used in Hungary，because of high work efficiency，excellent fatigue and impact resistance，no need for deceleration device.So our company has designed supporting cylinder for customers from Hungary.

Introduction to supporting cylinder:

When the supporting cylinder needs to be stored for a period of time, please follow the recommended methods: The supporting cylinder should be stored in a dry, clean, non-corrosive gas indoor environment, pay attention to protect the supporting cylinder from internal corrosion and external damage. If the indoor requirements cannot be met, the hardened and well-drained ground should be cushioned at least 30cm, and the upper part should be covered with waterproof storage. The oil supporting cylinder should not be in direct contact with water vapor for a long time. The supporting cylinder should be placed as vertically as possible with the piston rod facing up, which minimizes corrosion due to possible condensation in the supporting cylinder and permanent deformation of the seal due to the piston and rod weight. (When the shield is stored in the shield machine, the support shoe is placed upward). Keep the oil port protective cover until the pipe is connected. For long-term storage, the protection should be added on both sides of the piston of the supporting cylinder Before working, the supporting cylinder must be run repeatedly with low pressure (greater than the starting pressure) to discharge the air in the supporting cylinder before normal work. The oil inlet and outlet and the joint must be tightly fastened with a combination pad to prevent oil leakage.

The cavitation of the supporting cylinder has a great influence, and to avoid it, it is necessary to use the hydraulic oil reasonably and ensure the quality of the hydraulic oil. If the anti-foam property of the oil is poor, it is easy to produce foam, resulting in cavitation. Secondly, the change frequency of oil pressure is too fast and too high, which will also directly cause the formation of bubbles and accelerate the rupture rate of bubbles. The test shows that the speed of cavitation will be accelerated in the part with high frequency of pressure change. For example, at the inlet and outlet of the supporting cylinder, due to the relatively high frequency of pressure changes, the degree of cavitation is also relatively higher than that of other parts. In addition, overheating of the oil will also increase the probability of cavitation.

In use, the supporting cylinder should try to avoid the friction iron powder or iron filings formed by buffering the plunger. When the matching gap of the buffer device is small and the transverse load on the piston rod is large, the sintering phenomenon may be caused. These friction iron powder or the metal fragments that have fallen off as a result of sintering will remain in the supporting cylinder.

The definition of the minimum starting pressure of the supporting cylinder refers to the minimum working pressure of the supporting cylinder in the no-load state, which is a comprehensive index reflecting the manufacturing and assembly accuracy of the supporting cylinder parts and the size of the sealing friction.

Answers to some questions about supporting cylinder:

What is the problem that the cylinder stroke is not in place?
1. Mechanical cause: the piston rod bends; If there is a synchronous cylinder, the stroke of the two cylinders may be different. 2. Hydraulic reason: the system back pressure is too large; The actuator load increases while the system pressure decreases. The electric is not sent, the reversing valve is not reset or stuck, the oil is too dirty, there is gas in the system, the external inertia load is too large, and the cylinder stroke is not in place.

How to set the stroke of the cylinder?
Self-design should be based on product demand and practical application. The stroke of standard cylinder depends on the parameters the customer requires. The hydraulic cylinder is a linear motion actuator whose output force is proportional to the effective area of the piston and the pressure difference on both sides. Its function is to convert hydraulic energy into mechanical energy. The input of the hydraulic cylinder is the flow rate and pressure of the fluid, and the output is the speed and force of the linear motion. The piston of the hydraulic cylinder can complete the linear reciprocating movement, and the linear displacement of the output is limited. Hydraulic cylinder is an energy conversion device that converts hydraulic energy into mechanical energy of reciprocating linear motion. The hydraulic cylinder is basically composed of cylinder body, cylinder head, piston and piston rod, sealing device, buffer device and exhaust device.