High quality hydraulic equipment manufacturers!
TELL:+8613184968882

servo cylinder Sold to France

Release time:2023-11-19 14:06:42 Hits: Current position: Home > News

This article mainly introduces:

France hydraulic cylinder,servo cylinder manufacturer,servo cylinder

France servo cylinder

(France servo cylinder,produced by Hengyu Hydraulic Cylinder Factory)

servo cylinder are widely used in France,because of high work efficiency,excellent fatigue and impact resistance,no need for deceleration device.So our company has designed servo cylinder for customers from France.

Introduction to servo cylinder:

When the servo cylinder is in use, measures should be added to prevent the intrusion of pollutants. Effective measures should be taken to control the intrusion of pollutants, such as installing high-efficiency air filters in the tank breathing holes, new oil must be filtered, etc., but also must improve the anti-pollution ability of the servo cylinder itself. In the seriously polluted environment, it is more important to pay attention to, such as the underground oil servo cylinder should use fluorine rubber (FRM) and nitrile rubber (NBR) dust ring, and the ground mechanical servo cylinder should use nitrile rubber dust ring; The filter device is added to the oil inlet of the servo cylinder of the dump truck, construction machinery, work platform and other equipment, and in order to reduce the oil inlet resistance, the flow area should be increased as much as possible, which can effectively reduce the particle pollution from the system.

servo cylinder can not drive the load troubleshooting: oil pressure is too low. servo cylinder selection specifications are too small. Leakage in servo cylinder or associated hydraulic system element.

Do not enter foreign bodies when installing the servo cylinder block. The place where the installation operation is carried out, the conditions are not good, and foreign bodies can be entered unconsciously. Therefore, the installation site must be cleaned up around, especially the place where the parts are placed must be cleaned, so that there is no dirt.

Causes and countermeasures of oil servo cylinder leakage: Cast iron ring seal allows a certain degree of internal leakage. The impurities in the servo cylinder will lead to premature wear of the piston seal, replace the piston seal; If the servo cylinder is visibly scarred, the servo cylinder must be replaced. It can be pressurized at one end of the servo cylinder and opened at the other end of the oil port to observe whether there is obvious internal leakage at the end of the oil port. Most servo cylinder piston drift may not come from the servo cylinder, the above method to determine the servo cylinder without internal leakage is helpful to determine the problem of the hydraulic system related components.

Answers to some questions about servo cylinder:

Is it normal for the cylinder to turn black?
Cylinder blackening is a soft fault: 1. It does not affect the normal operation of your equipment. 2. Cylinder blackening involves a lot of things: hydraulic oil, oil seal material, piston rod coating, etc. These three things are not determined by the manufacturer because these three things are provided by other manufacturers. If the equipment is not due to high temperature caused by the black cylinder, you do not have to worry too much because your excavator can still work normally. If you feel uncomfortable, you can choose to replace the cylinder or replace the hydraulic oil.

What hydraulic oil does servo cylinder generally use?
The medium used by the cylinder generally depends on the working condition of the use, including pressure, installation environment, sealing material, etc. I think the first thing to consider is the impact of the sealing material. Mineral oil is a good choice if it is not too fire-resistant or used in a high temperature environment. 1, servo cylinder features: closed-loop servo control, control accuracy of 0.01mm; Precise control of thrust, increase pressure sensor, control accuracy up to 1%; It is easy to connect with PLC and other control systems to achieve high precision motion control. Low noise, energy saving, clean, high rigidity, impact resistance, long life, simple operation and maintenance. 2, the servo cylinder can be fault-free in harsh environments, and the protection level can reach IP66.

Back to list Recommended article

Leave a message if you have any questions.

Send
Email

Email:hsslrubbertech@gmail.com7x24 hours

Glad to receive your consultation!:

Service
Tel

+8613184968882
7x24hours service

Add
Wechat

Add Wechat
TOP