tilting furnace hydraulic cylinder Sold to Kuwait

This article mainly introduces:

Kuwait hydraulic cylinder,tilting furnace hydraulic cylinder manufacturer,tilting furnace hydraulic cylinder

(Kuwait tilting furnace hydraulic cylinder,produced by Hengyu Hydraulic Co., Ltd）

tilting furnace hydraulic cylinder are widely used in Kuwait，because of no need for deceleration device，long service life，smooth movement.So our company has designed tilting furnace hydraulic cylinder for customers from Kuwait.

Introduction to tilting furnace hydraulic cylinder:

The tilting furnace hydraulic cylinder should be used correctly and maintained regularly. The tilting furnace hydraulic cylinder should be deflated before use, the buffer regulating valve should be adjusted to a reasonable position, the cleanliness of the oil should be checked regularly, the dust on the tilting furnace hydraulic cylinder should be cleaned regularly, and attention should be paid to waterproof and fireproof.

When the tilting furnace hydraulic cylinder wear is serious, you can try to use an alloy scraper to shave grooves with a depth of more than 1mm on the surface of the slip injury, then clean the grooves with acetone, apply the adjusted TS311 anti-wear repair agent on the polished surface with the tilting furnace hydraulic cylinder inner diameter copying plate, and scrape it flat vigorously to ensure compaction and higher than the inner surface of the tilting furnace hydraulic cylinder. After curing, polish to leave a finishing margin. Finally, the overall size, shape tolerance and roughness of the tilting furnace hydraulic cylinder can meet the requirements by grinding. However, the life and reliability of this repair tilting furnace hydraulic cylinder are not high.

tilting furnace hydraulic cylinders in series, parallel and series parallel. Series: In the tilting furnace hydraulic cylinder, the oil inlet of the subsequent reversing valve is the supply of the previous oil return, and there is no separate oil return circuit connected with the oil return in each valve. Series: In the tilting furnace hydraulic cylinder, the oil inlet of the subsequent reversing valve is the supply of the previous oil return, and there is no separate oil return circuit connected with the oil return in each valve. Parallel: the pressure oil in the tilting furnace hydraulic cylinder is connected with the inlet oil of each reversing valve, and the return oil is collected by the return oil circuit. Series parallel: For this one, compared with the simple series and parallel, it is slightly more complicated, but it is not impossible to understand. The series refers to the oil in the tilting furnace hydraulic cylinder, which is in series form, but can not form a series circuit, and the parallel refers to the oil return circuit of each valve, which is in parallel.

We can not just consider the price and ignore the quality when we purchase the tilting furnace hydraulic cylinders. Now some manufacturers produce unqualified products in order to reduce costs, the piston rod is not adjusted, the rod coating is not enough, the tilting furnace hydraulic cylinder finish can not reach, the guide sleeve should use copper, but instead of ductile iron, although the cost is reduced, the quality of the tilting furnace hydraulic cylinder is not required.

Answers to some questions about tilting furnace hydraulic cylinder:

What is hydraulic cylinder internal leakage and external leakage?
The internal leakage of the hydraulic cylinder refers to the leakage of the piston head seal of the double-acting cylinder, and the leakage occurs inside the cylinder; The external leakage refers to the leakage phenomenon between the cylinder head (or cylinder guide sleeve) and the plunger rod (or piston rod) and the seal between the guide sleeve and the cylinder block, and the oil in the hydraulic cylinder leaks to the outside.

Why does the hydraulic cylinder not return?
For a spring return cylinder, it is possible that 1, the spring is damaged. You can check it for processing. 2, the oil in the oil path is not unloaded, causing it to be unable to reset. 3, the cylinder piston is dead, resulting in no position. For double-acting cylinders, it is possible to: 1, the spool is not reversed, or is not changed to the correct position, check whether the reversing valve is normal (and whether there is electricity). 2, the cylinder piston is dead, resulting in no position, check and treatment can be. 3, the return oil pressure is insufficient, the inlet oil is not unloaded, the operation is not smooth. For reference only.