punch machine hydraulic cylinder Sold to Bangladesh

This article mainly introduces:

Bangladesh hydraulic cylinder,punch machine hydraulic cylinder manufacturer,punch machine hydraulic cylinder

(Bangladesh punch machine hydraulic cylinder,produced by Hebei Hengyu company）

punch machine hydraulic cylinder are widely used in Bangladesh，because of no transmission clearance，powerful torque，clever hydraulic energy conversion.So our company has designed punch machine hydraulic cylinder for customers from Bangladesh.

Introduction to punch machine hydraulic cylinder:

What kind of process is used in the punch machine hydraulic cylinder to make high-quality punch machine hydraulic cylinder products: the body is the main component of the punch machine hydraulic cylinder, mining single pillar, hydraulic support, gun tube and other products, and its processing quality directly affects the life and reliability of the entire product. Body processing requirements are high, the internal surface roughness requirements are Ra0.4 ~ 0.8&um, the coaxiality, wear resistance requirements are strict. The basic feature of body is deep hole processing, which has always troubled the processing personnel. The punch machine hydraulic cylinder products of our company mainly use rolling processing, because the surface layer has surface residual compressive stress, which helps to close the surface micro-cracks and hinder the expansion of erosion. Thus, the corrosion resistance of the surface can be improved, and the fatigue crack can be delayed or expanded, and the fatigue strength of the body can be improved. The correct rolling process of the punch machine hydraulic cylinder block: broaching block - fine boring block - grinding block. The rolling method is: broaching block - fine boring block - rolling block, the process is 3 parts, but the time is compared: grinding 1 meter of the block is about 1-2 days, rolling 1 meter of the block is about 10-30 minutes. Input comparison: grinding machine or quilting machine (tens of thousands - millions), rolling knife (ten thousand - tens of thousands). After rolling, the surface roughness of the hole decreases from RA3.2-6.3um before rolling to RA0.4-0.8&um, the surface hardness of the hole increases by about 30%, and the fatigue strength of the inner surface of the punch machine hydraulic cylinder increases by 25%. If the service life of the punch machine hydraulic cylinder is only considered, it is increased by 2 to 3 times, and the efficiency of the boring and rolling process is about 3 times higher than that of the grinding process. punch machine hydraulic cylinder misoperation or operation failure may be caused by the following reasons, you can start from these aspects of the investigation: (1) spool stuck or valve hole blocked. When the spool of the flow valve or direction valve is stuck or the valve hole is blocked, the punch machine hydraulic cylinder is prone to misoperation or operation failure. At this time, the contamination of the oil should be checked; Check whether dirt or colloidal deposits are stuck in the spool or blocking the valve hole; Check the wear of the valve body, clean and replace the system filter, clean the fuel tank, and replace the hydraulic medium. (2) The piston rod and punch machine hydraulic cylinder are stuck or the punch machine hydraulic cylinder is blocked. At this time, no matter how to manipulate, the punch machine hydraulic cylinder does not move or moves very little. At this time, check whether the piston and piston rod seal is too tight, whether it enters the dirt and gum deposits: whether the shaft line of the piston rod and the punch machine hydraulic cylinder is in the center, whether the wearing parts and seals are invalid, and whether the load is too large.

The definition of the minimum starting pressure of the punch machine hydraulic cylinder refers to the minimum working pressure of the punch machine hydraulic cylinder in the no-load state, which is a comprehensive index reflecting the manufacturing and assembly accuracy of the punch machine hydraulic cylinder parts and the size of the sealing friction.

The punch machine hydraulic cylinder pipe should not be left behind when deburring at both ends after the fixed length processing. In addition, the placement of steel pipes near the site of welding pipeline operations is the cause of welding foreign objects. The pipes placed near the welding operation site should be sealed. It must also be noted that pipe fitting materials should be fully prepared on a dust-free workbench.

punch machine hydraulic cylinder body inspection: The inner surface of the punch machine hydraulic cylinder and the piston seal are the main factors causing the leakage in the punch machine hydraulic cylinder, if the punch machine hydraulic cylinder has a longitudinal tensile mark, even if the new piston seal is replaced, it can not effectively eliminate the fault, the inner surface of the punch machine hydraulic cylinder mainly checks whether the dimensional tolerance and shape and position tolerance meet the technical requirements, there is no longitudinal tensile mark, and measures the depth of the longitudinal tensile mark, in order to take the corresponding solution.

Answers to some questions about punch machine hydraulic cylinder:

What are the connection methods of the hydraulic cylinder? The connection modes of the cylinder and the actuator are earring connection, hinge shaft connection, thread connection, etc. The connection modes of tubing and cylinder are threaded connection, flange connection, etc.

What is the cause of the deep scratch of the cylinder?
The following reasons can cause the cylinder to be scratched. 1: Hydraulic oil containing particulate impurities into the hydraulic cylinder, these particulate impurities stuck between the piston rod and the guide ring (or stuck between the piston and the inner wall of the cylinder), when the piston movement in the cylinder will scratch the piston rod, the phenomenon of the inner wall of the cylinder, the more particles, the larger the scratch marks the deeper and more obvious. 2: The body of the cylinder itself. Due to assembly or design reasons, the coaxial error between the piston rod, piston, cylinder, guide ring and other parts is too large, or the cylinder, piston rod straightness error is too large, so that the piston rod and the guide ring interference between the cylinder, this mechanical interference will certainly lose the piston rod or cylinder wall.