rolling mill cylinder Sold to Kenya

This article mainly introduces:

Kenya hydraulic cylinder,rolling mill cylinder manufacturer,rolling mill cylinder

(Kenya rolling mill cylinder,produced by Hengyu Hydraulic Co., Ltd）

rolling mill cylinder are widely used in Kenya，because of excellent fatigue and impact resistance，no need for deceleration device，long service life.So our company has designed rolling mill cylinder for customers from Kenya.

Introduction to rolling mill cylinder:

If the rolling mill cylinder operation failure, you can start from these aspects to troubleshoot: (1) the hydraulic system control pressure is too low. The throttling resistance in the control line may be too large, the flow valve is improperly adjusted, the control pressure is inappropriate, and the pressure source is disturbed. At this time, the control pressure source should be checked to ensure that the pressure is adjusted to the specified value of the system; (2) Air enters the hydraulic system. Mainly because there is a leak in the system. At this time, check the liquid level of the hydraulic tank, the seals and fittings on the oil suction side of the hydraulic pump, and whether the oil suction filter is too dirty. If so, the hydraulic oil should be replenished, seals and fittings should be treated, and the coarse filter element should be cleaned or replaced. (3) The initial action of the rolling mill cylinder is slow. In the case of low temperature, the hydraulic oil viscosity is large, poor flow, resulting in slow rolling mill cylinder action. The improvement method is to replace the hydraulic oil with better viscosity and temperature performance If the rolling mill cylinder is weak and cannot push the load, please check the internal leakage problem. The internal leakage of the rolling mill cylinder includes the leakage caused by excessive wear of the rolling mill cylinder block seal, the piston rod and the seal cover seal and the piston seal. The cause of sealing leakage between the piston rod and the seal cover is that the seal is wrinkled, squeezed, torn, worn, aging, deterioration, deformation, etc., and a new seal should be replaced at this time. The main cause of excessive piston seal wear is improper adjustment of the speed control valve, resulting in excessive back pressure and improper seal installation or hydraulic oil contamination. The second is that foreign bodies enter the assembly and the quality of sealing materials is not good. The result is that the action is slow and weak, and in serious cases, it will cause damage to the piston and rolling mill cylinder, and the phenomenon of "pulling the rolling mill cylinder" appears. The treatment method is to adjust the speed control valve, and the necessary operations should be done according to the installation instructions.

When the rolling mill cylinder is installed, it is necessary to ensure that the direction of the connecting head at the top of the piston rod should be consistent with the direction of the rolling mill cylinder head, earring (or middle hinge shaft), and ensure the straightness of the whole piston rod during the advance and return process to prevent rigid interference and cause unnecessary damage.

When the hydraulic oil is not pumped into the rolling mill cylinder, it is necessary to check whether the tubing, oil circuit, especially the hose joint has been blocked, and the relevant oil circuit from the rolling mill cylinder to the pump should be checked in turn and blocked; Check whether the seal between the taper valve and the seat of the relief valve is good; Check whether the solenoid valve spring is damaged or whether the solenoid coil is burned out; Whether the oil circuit is switched is insensitive.

When purchasing the rolling mill cylinder, try to clarify the following parameters of the rolling mill cylinder: A. rolling mill cylinder diameter, rod diameter, stroke; B. Working pressure or rolling mill cylinder load; C. Working environment temperature; D. Working medium; E. Operating speed; F. Other parameters, such as connection form, mounting size, etc. In this way, the right rolling mill cylinder type can be found accurately and quickly.

Answers to some questions about rolling mill cylinder:

What is the reason why the hydraulic cylinder is not good at lifting?
There may be several situations 1, whether the slow one is worn 2, whether there is air in the slow cylinder 3, if the two cylinders are supplied by the same oil port, whether the slow joint is blocked (some processing residue will reach a certain oil port under a certain coincidence condition, This situation will not happen if it is not necessarily good before) 4, the oil seal in the slow cylinder leaks, causing the feed oil to leak from the return oil end. Point 4 is most likely because it is invisible and a technical failure. If it is a dual oil feed (separate oil feed), it is also necessary to check the oil supply system and the oil return system (valve type).

Is it normal for the cylinder to turn black?
Cylinder blackening is a soft fault: 1. It does not affect the normal operation of your equipment. 2. Cylinder blackening involves a lot of things: hydraulic oil, oil seal material, piston rod coating, etc. These three things are not determined by the manufacturer because these three things are provided by other manufacturers. If the equipment is not due to high temperature caused by the black cylinder, you do not have to worry too much because your excavator can still work normally. If you feel uncomfortable, you can choose to replace the cylinder or replace the hydraulic oil.