steering power cylinder Sold to Vietnam

This article mainly introduces:

Vietnam hydraulic cylinder,steering power cylinder manufacturer,steering power cylinder

(Vietnam steering power cylinder,produced by Hengyu Hydraulic Cylinder Factory）

steering power cylinder are widely used in Vietnam，because of smooth movement，high work efficiency，excellent fatigue and impact resistance.So our company has designed steering power cylinder for customers from Vietnam.

Introduction to steering power cylinder:

steering power cylinder installation precautions: Before installing the steering power cylinder into the system, the parameters on the steering power cylinder label should be compared with the parameters when ordering. The base of the steering power cylinder must have sufficient stiffness, otherwise the steering power cylinder will bend upward into a bow when pressurized, so that the piston rod will bend.

If the steering power cylinder operation failure, you can start from these aspects to troubleshoot: (1) the hydraulic system control pressure is too low. The throttling resistance in the control line may be too large, the flow valve is improperly adjusted, the control pressure is inappropriate, and the pressure source is disturbed. At this time, the control pressure source should be checked to ensure that the pressure is adjusted to the specified value of the system; (2) Air enters the hydraulic system. Mainly because there is a leak in the system. At this time, check the liquid level of the hydraulic tank, the seals and fittings on the oil suction side of the hydraulic pump, and whether the oil suction filter is too dirty. If so, the hydraulic oil should be replenished, seals and fittings should be treated, and the coarse filter element should be cleaned or replaced. (3) The initial action of the steering power cylinder is slow. In the case of low temperature, the hydraulic oil viscosity is large, poor flow, resulting in slow steering power cylinder action. The improvement method is to replace the hydraulic oil with better viscosity and temperature performance If the steering power cylinder is weak and cannot push the load, please check the internal leakage problem. The internal leakage of the steering power cylinder includes the leakage caused by excessive wear of the steering power cylinder block seal, the piston rod and the seal cover seal and the piston seal. The cause of sealing leakage between the piston rod and the seal cover is that the seal is wrinkled, squeezed, torn, worn, aging, deterioration, deformation, etc., and a new seal should be replaced at this time. The main cause of excessive piston seal wear is improper adjustment of the speed control valve, resulting in excessive back pressure and improper seal installation or hydraulic oil contamination. The second is that foreign bodies enter the assembly and the quality of sealing materials is not good. The result is that the action is slow and weak, and in serious cases, it will cause damage to the piston and steering power cylinder, and the phenomenon of "pulling the steering power cylinder" appears. The treatment method is to adjust the speed control valve, and the necessary operations should be done according to the installation instructions.

steering power cylinder abnormal sound, hysteresis phenomenon cause and elimination method: the piston rod is extended with abnormal sound and hysteresis, if the steering power cylinder is placed for a period of time, the steering power cylinder may enter the air, and the movement can be normal after dozens of repeated movements. If it still cannot be eliminated, check whether the load is aligned with the axis of the piston rod; Retracted piston rod installation helps to align the load with the piston rod. If the flow is unstable, it will also lead to abnormal movement of the piston rod. Check the relevant components of the hydraulic system.

If the seal of the steering power cylinder is abnormal wear, you can check whether the speed control valve is improperly adjusted, resulting in too high back pressure and improper installation of the seal or hydraulic oil contamination. The second is whether there is a foreign body entering the assembly and the quality of the sealing material is not good. The result is that the action is slow and weak, and in serious cases, it will cause damage to the piston and steering power cylinder, and the phenomenon of "pulling the steering power cylinder" appears. The treatment method is to adjust the speed control valve, and the necessary operation and improvement should be done according to the installation instructions.

Answers to some questions about steering power cylinder:

What kind of seal ring we should choose for 120Mpa hydraulic cylinder?
The sealing rings used in mining machinery are high pressure, which can reach 150MPa. It is generally composed of three parts, the guide ring, the sealing body and the elastomer. It's not a special structure. It's more mature. Usually said mountain circle, bud circle.

Do the collecting cylinder, distributing cylinder and distributing cylinder on the organic heat carrier boiler need to be notified separately as the pressure vessel for construction?
Do not need to be installed as a separate pressure vessel to inform, according to the organic heat carrier boiler can be informed. Write a "special equipment installation, renovation and maintenance notice" issued on it.