tilting furnace hydraulic cylinder Sold to Austria

This article mainly introduces:

Austria hydraulic cylinder,tilting furnace hydraulic cylinder manufacturer,tilting furnace hydraulic cylinder

(Austria tilting furnace hydraulic cylinder,produced by Hebei Hengyu company）

tilting furnace hydraulic cylinder are widely used in Austria，because of simple structure and reliable operation，excellent temperature resistance，no transmission clearance.So our company has designed tilting furnace hydraulic cylinder for customers from Austria.

Introduction to tilting furnace hydraulic cylinder:

tilting furnace hydraulic cylinder buffer valve inspection and maintenance: For the valve buffer tilting furnace hydraulic cylinder, the focus should be on checking the wear of the buffer valve spool and seat. Once it is found that the amount of wear increases and the seal fails, it should be replaced. It can also be repaired by using abrasive spool and seat matching grinding method.

When installing the tilting furnace hydraulic cylinder pipe, the pipe should be cleaned after installation, and should not pass through the tilting furnace hydraulic cylinder block, and the by-pass pipe must be installed in front of the oil port of the tilting furnace hydraulic cylinder block. This is important. Otherwise, the foreign body in the pipeline will enter the tilting furnace hydraulic cylinder, and once it enters, it is difficult to exclude it, but it becomes a foreign body transported to the tilting furnace hydraulic cylinder. Moreover, when cleaning, the removal method of foreign bodies entered in the installation pipeline operation should be considered. In addition, the corrosion in the pipe should be pickling and other procedures before the pipe installation, and the rust must be completely removed.

When installing the tilting furnace hydraulic cylinder, the axial ends of the tilting furnace hydraulic cylinder cannot be fixed. Due to the effect of liquid pressure and thermal expansion in the tilting furnace hydraulic cylinder, there is axial expansion. If the two ends of the tilting furnace hydraulic cylinder are fixed, all parts of the tilting furnace hydraulic cylinder will be deformed. When disassembling the tilting furnace hydraulic cylinder, it is strictly forbidden to hammer the tilting furnace hydraulic cylinder and the piston surface, such as the tilting furnace hydraulic cylinder hole and the piston surface is damaged, do not allow sandpaper grinding, to use a fine oil stone carefully grinding. The clearance between the guide sleeve and the piston rod should meet the requirements.

The tilting furnace hydraulic cylinder should be avoided for a long time without use, if it is indeed idle for a long time for some reason, it should also be regularly turned on for empty operation, so that its parts can be fully lubricated, so as to avoid rust on the working surface and affect the normal work in the future. (If it cannot be turned on and run, a small amount of lubricating oil can be applied on its outer surface for protection) ' The use of the tilting furnace hydraulic cylinder should pay attention to: the operation should be as far away from the tilting furnace hydraulic cylinder as possible, to avoid falling objects, knocking, rubbing the tilting furnace hydraulic cylinder coating. When cleaning the tilting furnace hydraulic cylinder, only use soft materials (such as cotton) to wipe, and do not scratch high-hardness materials. Do not use the tilting furnace hydraulic cylinder when the oil temperature exceeds 70 ° C.

Answers to some questions about tilting furnace hydraulic cylinder:

Classification and application of cylinders.
Hydraulic cylinder is divided into single acting hydraulic cylinder, double acting cylinder, combined hydraulic cylinder, swing hydraulic cylinder. Single acting cylinder is divided into plunger type hydraulic cylinder, single piston rod hydraulic cylinder, double piston rod hydraulic cylinder, telescopic hydraulic cylinder. Plunger type hydraulic cylinder: the plunger moves only in one direction, and the return stroke is to push the plunger back using its own weight or load. Single piston rod hydraulic cylinder: The piston moves only in one direction, and the return stroke is to push the plunger back using dead weight or load. Double piston rod hydraulic cylinder: both sides of the piston are equipped with piston rods, and pressure oil can only be supplied to one side of the piston. The return stroke usually uses spring force, gravity or external force. Telescopic hydraulic cylinder: It obtains long stroke with short cylinder. The hydraulic oil is pushed out from large to small section by section, and the external force is reduced from small to large.

What is the cylinder with rod cavity, what is the rodless cavity.
The rod cavity is the end of the piston rod, the rodless cavity is the end without the piston rod.