sanitation truck hydraulic cylinder Sold to Saudi Arabia

This article mainly introduces:

Saudi Arabia hydraulic cylinder,sanitation truck hydraulic cylinder manufacturer,sanitation truck hydraulic cylinder

(Saudi Arabia sanitation truck hydraulic cylinder,produced by Hengyu Hydraulic Co., Ltd）

sanitation truck hydraulic cylinder are widely used in Saudi Arabia，because of no transmission clearance，simple structure and reliable operation，excellent temperature resistance.So our company has designed sanitation truck hydraulic cylinder for customers from Saudi Arabia.

Introduction to sanitation truck hydraulic cylinder:

Before the sanitation truck hydraulic cylinder is removed, the relief valve should be loosened to reduce the pressure of the hydraulic circuit to zero, and then the power supply should be cut off to stop the hydraulic device. After loosening the oil port piping, the oil plug should be applied to plug the oil port.

sanitation truck hydraulic cylinder is the most important part of construction machinery, the traditional processing method is: broaching sanitation truck hydraulic cylinder block - fine boring sanitation truck hydraulic cylinder block - grinding sanitation truck hydraulic cylinder block. The rolling method is: broaching sanitation truck hydraulic cylinder block - fine boring sanitation truck hydraulic cylinder block - rolling sanitation truck hydraulic cylinder block, the process is 3 parts, but the time is compared: grinding 1 meter of the sanitation truck hydraulic cylinder block is about 1-2 days, rolling 1 meter of the sanitation truck hydraulic cylinder block is about 10-30 minutes. Input comparison: grinding machine or quilting machine (tens of thousands - millions), rolling knife (ten thousand - tens of thousands). After rolling, the surface roughness of the hole decreases from RA3.2-6.3 μm before rolling to Ra0.4 ~ 0.8μm, the surface hardness of the hole increases by about 30%, and the fatigue strength of the inner surface of the sanitation truck hydraulic cylinder increases by 25%. If the sanitation truck hydraulic cylinder life is only considered, it is increased by 2 to 3 times, and the boring and rolling process is 3 times more efficient than the grinding process In particular, if you want to make high-quality sanitation truck hydraulic cylinders, you must take the rolling production process. After the sanitation truck hydraulic cylinder is rolled, there is no sharp tiny edge on the surface, and long-term motion friction will not damage the seal ring or seal, which is particularly important in the hydraulic industry.

The cavitation of the sanitation truck hydraulic cylinder has a great influence, and to avoid it, it is necessary to use the hydraulic oil reasonably and ensure the quality of the hydraulic oil. If the anti-foam property of the oil is poor, it is easy to produce foam, resulting in cavitation. Secondly, the change frequency of oil pressure is too fast and too high, which will also directly cause the formation of bubbles and accelerate the rupture rate of bubbles. The test shows that the speed of cavitation will be accelerated in the part with high frequency of pressure change. For example, at the inlet and outlet of the sanitation truck hydraulic cylinder, due to the relatively high frequency of pressure changes, the degree of cavitation is also relatively higher than that of other parts. In addition, overheating of the oil will also increase the probability of cavitation.

Because of the slightly complex structure of the buffer sanitation truck hydraulic cylinder, sometimes there will be problems, such as when the sanitation truck hydraulic cylinder with the buffer device is started in reverse, the piston often stops temporarily or reverses. Elimination method: The orifice of the check valve is too small, so that the amount of oil entering the buffer chamber is too small, and even a vacuum occurs, so the above fault phenomenon will occur when the buffer plunger leaves the end cover. In this regard, the orifice of the check valve should be increased.

Answers to some questions about sanitation truck hydraulic cylinder:

What is the difference between hollow and solid oil cylinders?
Hollow solid cylinder, according to conventional understanding, refers to whether the piston rod is solid or hollow. General ordinary hydraulic cylinder, the piston rod is solid structure. Hollow hydraulic cylinder refers to a hollow piston rod structure of the hydraulic cylinder, see the attached figure. Piston rod hollow function: 1, the piston rod hollow, the middle can be threaded rod. For example, the clamping cylinder with a sawing machine, the piston rod center threading rod, part of the stroke through manual, part of the stroke hydraulic automatic walk. 2, the hollow hole of the piston rod can be used to direct the oil circuit to achieve special oil circuit. 3, the cylinder is relatively large, the piston rod is relatively large, and the stroke is longer, in this case, the piston rod is hollow to reduce the movement friction and lateral force.

Why is the hydraulic cylinder of the larger excavator arm upside down?
The weight of the excavating arm of a large excavator will be very heavy, and an oil cylinder has two cavities, one is a rod cavity, and the other is a rodless cavity. The lifting force of the excavator is the product of the ortho-projection area of the piston rod cavity by the oil pressure, so the strength of the rodless cavity is much greater than that of the rod cavity. And the parallel bars with the piston rod facing down are also conducive to assembly and future maintenance. So a large excavator has to keep the cylinder facing down.