reciprocating cylinder Sold to Turkmenistan

This article mainly introduces:

Turkmenistan hydraulic cylinder,reciprocating cylinder manufacturer,reciprocating cylinder

(Turkmenistan reciprocating cylinder,produced by Hebei Hengyu company）

reciprocating cylinder are widely used in Turkmenistan，because of clever hydraulic energy conversion，simple structure and reliable operation，excellent temperature resistance.So our company has designed reciprocating cylinder for customers from Turkmenistan.

Introduction to reciprocating cylinder:

When using the reciprocating cylinder product, be sure to operate safely in accordance with the specification documents provided by the manufacturer, and pay attention to protecting the reciprocating cylinder block. If the reciprocating cylinder block is damaged, it will cause adverse consequences: ① The material debris extruded from the scratch groove will be embedded in the seal, which may cause new scratch area marks while damaging the working parts of the seal during operation. ② Deterioration of the surface roughness of the inner wall of the reciprocating cylinder, increase friction, easy to produce crawling phenomenon. ③ Increase the internal leakage of the reciprocating cylinder, so that the working efficiency of the reciprocating cylinder is reduced.

When the reciprocating cylinder is in use, measures should be added to prevent the intrusion of pollutants. Effective measures should be taken to control the intrusion of pollutants, such as installing high-efficiency air filters in the tank breathing holes, new oil must be filtered, etc., but also must improve the anti-pollution ability of the reciprocating cylinder itself. In the seriously polluted environment, it is more important to pay attention to, such as the underground oil reciprocating cylinder should use fluorine rubber (FRM) and nitrile rubber (NBR) dust ring, and the ground mechanical reciprocating cylinder should use nitrile rubber dust ring; The filter device is added to the oil inlet of the reciprocating cylinder of the dump truck, construction machinery, work platform and other equipment, and in order to reduce the oil inlet resistance, the flow area should be increased as much as possible, which can effectively reduce the particle pollution from the system.

Most of the failure of the reciprocating cylinder is because there is a foreign body in the reciprocating cylinder into the failure of the reciprocating cylinder, the most problematic is that it is difficult to determine when the foreign body is into the reciprocating cylinder. After a foreign body enters, if the outer side of the sliding surface of the piston is equipped with a seal with a lip edge, then the lip edge of the seal can scrape the foreign body when working, which is beneficial to avoid scratching. However, the piston equipped with 0-shaped sealing ring has a sliding surface at both ends, and foreign bodies are sandwiched between this sliding surface, which is easy to form scars.

Factors that should be considered when selecting the oil seal in the reciprocating cylinder: some specific factors should be taken into account when selecting the oil seal in the reciprocating cylinder, so as to have correct consideration and get accurate results, and then avoid wrong selection. The factors and aspects that should be taken into account are eight: reciprocating cylinder diameter, piston rod diameter, piston rod and piston groove size, reciprocating cylinder working pressure, reciprocating cylinder movement speed, hydraulic system oil temperature and reciprocating cylinder working environment.

Answers to some questions about reciprocating cylinder:

Where is the cylinder used? What is it used for? Can it be used in cars?
Cylinders can be used as actuator in hydraulic system. Such as hydraulic jacks, dump truck box lifting device, dodging (snow) machine loader bucket lifting device. Hydraulic cylinders are also widely used in car cranes. It's all about cars.

How does the cylinder of the shearing machine work?
Plate shear is a machine that cuts a sheet with a reciprocating straight motion from one blade to another. Through the moving upper blade and the fixed lower blade, the shear force is applied to the metal sheet of various thicknesses with a reasonable blade gap, so that the sheet is broken and separated according to the required size. Shearing machine belongs to one of the forging machinery, the main role is the metal processing industry. Products are widely used in aviation, light industry, metallurgy, chemical industry, construction, shipbuilding, automobile, electric power, electrical appliances, decoration and other industries to provide the required special machinery and complete sets of equipment. Working principle: The hydraulic system is used to drive the hydraulic cylinder to output a strong shear force to complete the shearing work.