reset cylinder Sold to Slovakia

This article mainly introduces:

Slovakia hydraulic cylinder,reset cylinder manufacturer,reset cylinder

(Slovakia reset cylinder,produced by Hengyu Hydraulic Cylinder Factory）

reset cylinder are widely used in Slovakia，because of high work efficiency，excellent fatigue and impact resistance，no need for deceleration device.So our company has designed reset cylinder for customers from Slovakia.

Introduction to reset cylinder:

When the reset cylinder thrust is insufficient, check the hydraulic circuit for leaks. Including leakage of valves and hydraulic lines. The inspection method is to check and eliminate the leakage of the hydraulic connection line by manipulating the reversing valve. Also consider the relief valve. If the relief valve enters the dirt and jams the spool, so that the relief valve is normally open, the hydraulic oil will flow directly back to the tank through the relief valve bypass, resulting in no oil in the reset cylinder. If the load is too large, although the regulating pressure of the relief valve has reached the maximum rating, the reset cylinder still cannot get the thrust required for continuous action without action. If the regulating pressure is low, the pressure is insufficient to achieve the required vertebra force, which is manifested as insufficient thrust. Check and adjust the relief valve at this time.

How the cavitation of the reset cylinder is formed: With the gradual rise of pressure, the gas in the oil will become bubbles, when the pressure rises to a certain limit value, these bubbles will break under the action of high pressure, so that the high temperature and high pressure gas will quickly act on the surface of the parts, resulting in cavitation of the reset cylinder, resulting in corrosive damage to the parts.

The difference between the integral reset cylinder and the split reset cylinder: The integral reset cylinder and the split reset cylinder in the reset cylinder are two different reset cylinders, and they are very different. The whole reset cylinder, which is cast in one body, is not prone to problems such as oil leakage; The split reset cylinder is welded twice, so if it is not handled well at the welding, it is prone to problems such as oil leakage and reset cylinder damage. Therefore, it is obvious that the answer to this question is for difference.

The "O" ring can be used as an auxiliary seal inside the reset cylinder, and the elastic force of the "O" ring makes the sealing slip ring close to the sealing surface, generating sealing pressure to achieve sealing. When the internal hydraulic pressure increases, the "O" ring will further deform and squeeze the slip ring, thereby increasing the sealing pressure and improving the sealing performance. The structure has the characteristics of low friction coefficient, good wear resistance, automatic compensation for wear and absorption of hard particles in the reset cylinder, and can be completely sealed.

Answers to some questions about reset cylinder:

How to choose cylinder size, pump type, motor power for a 30-ton press?
30 tons = 30,000 kg. It is expected to use a 16 mpa oil pump, then the cylinder area =30000/(160x3.14) and then square, the cylinder bore is 150 mm. Calculated at 500 mm travel per minute, the flow rate per minute is :0.75^2x3.14x5=8.8 liters/minute. Motor power =8.8x16/60=2.355. A 9 L/min, 16 mpa pump is available. Piston diameter 150 mm cylinder. 3 kW motor.

How to achieve hydraulic cylinder self-locking?
Hydraulic cylinder self-locking is divided into oil self-locking and mechanical self-locking. The oil self-locking is equipped with a valve to maintain pressure, so that the hydraulic oil of the cylinder does not return to the tank, and the oil chamber of the cylinder is filled with a certain pressure of oil. However, this pressure holding self-locking is not very safe and reliable, and the plunger will slowly return if there is a leak. Mechanical self-locking is to install a nut on the plunger of the cylinder, and when the cylinder rises to the required position, the nut on the cylinder plunger is rotated to the end, and the cylinder block is in contact, so that the plunger will be fixed to the required height. When it is necessary to relieve the pressure, screw the nut on again and let the plunger return to the position. This kind of cylinder has a special name, called self-locking hydraulic cylinder.