High quality hydraulic equipment manufacturers!
TELL:+8613184968882

roller press hydraulic cylinder Sold to France

Release time:2023-11-30 10:59:59 Hits: Current position: Home > News

This article mainly introduces:

France hydraulic cylinder,roller press hydraulic cylinder manufacturer,roller press hydraulic cylinder

France roller press hydraulic cylinder

(France roller press hydraulic cylinder,produced by Hengyu Group)

roller press hydraulic cylinder are widely used in France,because of excellent temperature resistance,no transmission clearance,powerful torque.So our company has designed roller press hydraulic cylinder for customers from France.

Introduction to roller press hydraulic cylinder:

The roller press hydraulic cylinder requires that the filtration accuracy of the system is not less than the 80um, and the oil pollution should be strictly controlled, the oil should be kept clean, the performance of the oil should be checked regularly, and the necessary fine filtration and replacement of new working oil should be carried out.

When the roller press hydraulic cylinder is in use, measures should be added to prevent the intrusion of pollutants. Effective measures should be taken to control the intrusion of pollutants, such as installing high-efficiency air filters in the tank breathing holes, new oil must be filtered, etc., but also must improve the anti-pollution ability of the roller press hydraulic cylinder itself. In the seriously polluted environment, it is more important to pay attention to, such as the underground oil roller press hydraulic cylinder should use fluorine rubber (FRM) and nitrile rubber (NBR) dust ring, and the ground mechanical roller press hydraulic cylinder should use nitrile rubber dust ring; The filter device is added to the oil inlet of the roller press hydraulic cylinder of the dump truck, construction machinery, work platform and other equipment, and in order to reduce the oil inlet resistance, the flow area should be increased as much as possible, which can effectively reduce the particle pollution from the system.

In order to ensure the service life of the roller press hydraulic cylinder, the hydraulic system must be set up effective filtration to prevent pollution, the cleanliness of the oil should meet the ISO4406 standard, and the quality of the filtration should also meet the corresponding standards in ISO. The grade requirements of the filter are performed according to the actual working conditions of the system, but the minimum requirements are not less than 19/15 in ISO4406, that is, 24μ (β10≥75) in ISO4572.

The oil roller press hydraulic cylinder is a part of the hydraulic system, in the hydraulic system, to reasonably design the heat dissipation system, to prevent the oil temperature is too high is the key to keep the hydraulic oil temperature normal. The temperature of the system should be kept in a suitable range to reduce the energy released when the bubble bursts. While not affecting the normal circulation of the coolant, a certain amount of anti-corrosion additives can be appropriately added to inhibit rust. When operating the hydraulic system, we should strive to be stable, not too fast, too strong, and try to reduce the impact of hydraulic oil on hydraulic components.

Answers to some questions about roller press hydraulic cylinder:

How to set up the one-way cylinder hydraulic system?
Single acting oil cylinder, that is, an oil cylinder with an oil port, can use two three-way valves to control the cylinder action. The three oil ports are respectively connected to P (oil pump), A (oil cylinder), and T (oil tank). If the oil pump is to run continuously, an electromagnetic relief valve can be added. When the cylinder is not moving, the relief valve can unload the oil pump. You can also add a three-way four-way valve, the middle function is unloaded, two outlets: A connected to the fuel tank, B connected to the cylinder.

How to calculate cylinder pressure?
Hydraulic pressure area of cylinder × hydraulic pressure = output force of cylinder 200mm=20cm 100mm=10cm 15Mpa=150Kg/cm2 Cylinder thrust: 3.14×10×10 area ×150 pressure =47100Kg=47.1t cylinder pulling force: 3.14×(10×10-5×5) Area ×150 pressure =35325Kg=35.325t The above calculation did not consider the resistance of oil return, because you did not provide oil return pressure. But the impact should be small.

Back to list Recommended article

Leave a message if you have any questions.

Send
Email

Email:hsslrubbertech@gmail.com7x24 hours

Glad to receive your consultation!:

Service
Tel

+8613184968882
7x24hours service

Add
Wechat

Add Wechat
TOP