300 tons hydrauli ccylinder Sold to Denmark

This article mainly introduces:

Denmark hydraulic cylinder,300 tons hydrauli ccylinder manufacturer,300 tons hydrauli ccylinder

(Denmark 300 tons hydrauli ccylinder,produced by Hengyu Hydraulic Cylinder Factory）

300 tons hydrauli ccylinder are widely used in Denmark，because of long service life，smooth movement，high work efficiency.So our company has designed 300 tons hydrauli ccylinder for customers from Denmark.

Introduction to 300 tons hydrauli ccylinder:

When the initial action of the 300 tons hydrauli ccylinder is slow, please check the temperature of the hydraulic system, because in the case of low temperature, the viscosity of the hydraulic oil is large and the fluidity is poor, resulting in slow action of the 300 tons hydrauli ccylinder. The improvement method is to replace the hydraulic oil with good viscosity temperature performance, and the oil temperature at low temperature can be increased by heater or heating by the machine itself, and the normal working oil temperature of the system should be maintained at about 40 ° C.

If the 300 tons hydrauli ccylinder operation failure, you can start from these aspects to troubleshoot: (1) the hydraulic system control pressure is too low. The throttling resistance in the control line may be too large, the flow valve is improperly adjusted, the control pressure is inappropriate, and the pressure source is disturbed. At this time, the control pressure source should be checked to ensure that the pressure is adjusted to the specified value of the system; (2) Air enters the hydraulic system. Mainly because there is a leak in the system. At this time, check the liquid level of the hydraulic tank, the seals and fittings on the oil suction side of the hydraulic pump, and whether the oil suction filter is too dirty. If so, the hydraulic oil should be replenished, seals and fittings should be treated, and the coarse filter element should be cleaned or replaced. (3) The initial action of the 300 tons hydrauli ccylinder is slow. In the case of low temperature, the hydraulic oil viscosity is large, poor flow, resulting in slow 300 tons hydrauli ccylinder action. The improvement method is to replace the hydraulic oil with better viscosity and temperature performance If the 300 tons hydrauli ccylinder is weak and cannot push the load, please check the internal leakage problem. The internal leakage of the 300 tons hydrauli ccylinder includes the leakage caused by excessive wear of the 300 tons hydrauli ccylinder block seal, the piston rod and the seal cover seal and the piston seal. The cause of sealing leakage between the piston rod and the seal cover is that the seal is wrinkled, squeezed, torn, worn, aging, deterioration, deformation, etc., and a new seal should be replaced at this time. The main cause of excessive piston seal wear is improper adjustment of the speed control valve, resulting in excessive back pressure and improper seal installation or hydraulic oil contamination. The second is that foreign bodies enter the assembly and the quality of sealing materials is not good. The result is that the action is slow and weak, and in serious cases, it will cause damage to the piston and 300 tons hydrauli ccylinder, and the phenomenon of "pulling the 300 tons hydrauli ccylinder" appears. The treatment method is to adjust the speed control valve, and the necessary operations should be done according to the installation instructions.

The material of the sliding part of the 300 tons hydrauli ccylinder piston sintered casting piston will cause sintering phenomenon when subjected to large transverse load. In this case, the sliding part of the piston should be made of copper alloy or welded to such material.

When the 300 tons hydrauli ccylinder is customized, if there are high requirements for the quality of the 300 tons hydrauli ccylinder, it is best to use rolling processing, because the surface layer has surface residual compressive stress, which helps to close the surface of the small crack, preventing the expansion of erosion. Thus, the corrosion resistance of the surface can be improved, and the fatigue crack can be delayed or expanded, and the fatigue strength of the 300 tons hydrauli ccylinder can be improved. By rolling forming, a cold working hardening layer is formed on the rolling surface, which reduces the elastic and plastic deformation of the contact surface of the grinding pair, thereby improving the wear resistance of the inner wall of the 300 tons hydrauli ccylinder and avoiding the burn caused by grinding. After rolling, the reduction of surface roughness value can improve the matching property.

Answers to some questions about 300 tons hydrauli ccylinder:

How to distinguish large cavity and small cavity of excavator rod cylinder ?
Single rod piston cylinder is a form of cylinder that is used relatively most, and the boom, bucket, dozer shovel cylinder are all in this form. Among them, the rodless cavity is also called the large cavity, and the rodless cavity is also called the small cavity. Therefore, the cylinder cavity on the side with the exposed piston rod is the small cavity, and the cylinder cavity on the side without the exposed rod is the large cavity.

Two cylinders in parallel, how to solve the synchronization problem?
The following methods can be used to achieve parallel cylinder synchronization: 1, rigid mechanical synchronization. 2. The throttle valve or speed regulating valve is used in the circuit to adjust the synchronization. 3, the two cylinders use independent quantitative pump oil supply to achieve synchronization. 4. Synchronous motor is used in the loop to realize cylinder synchronization. 5, using the position sensor to measure the stroke position and control the cylinder synchronization through the electrical system.