unidirectional cylinder Sold to Bahrain

This article mainly introduces:

Bahrain hydraulic cylinder,unidirectional cylinder manufacturer,unidirectional cylinder

(Bahrain unidirectional cylinder,produced by Hebei Hengyu company）

unidirectional cylinder are widely used in Bahrain，because of no transmission clearance，powerful torque，clever hydraulic energy conversion.So our company has designed unidirectional cylinder for customers from Bahrain.

Introduction to unidirectional cylinder:

If the unidirectional cylinder slips or crawls, please check whether there is astringency inside the unidirectional cylinder, because the internal parts of the unidirectional cylinder are improperly assembled, the parts are deformed, worn or the shape and position tolerance is excessive, the action resistance is too large, so that the piston speed of the unidirectional cylinder changes with the different stroke position, and the slip or crawl occurs. Most of the reasons are due to poor assembly quality of parts, surface scars or sintered iron filings, so that the resistance increases, the speed decreases. For example, the piston is different from the piston rod or the piston rod is bent, the unidirectional cylinder or the piston rod is offset from the mounting position of the guide rail, and the sealing ring is too tight or too loose. The solution is to repair or adjust, replace damaged parts and remove iron filings.

What kind of process is used in the unidirectional cylinder to make high-quality unidirectional cylinder products: the body is the main component of the unidirectional cylinder, mining single pillar, hydraulic support, gun tube and other products, and its processing quality directly affects the life and reliability of the entire product. Body processing requirements are high, the internal surface roughness requirements are Ra0.4 ~ 0.8&um, the coaxiality, wear resistance requirements are strict. The basic feature of body is deep hole processing, which has always troubled the processing personnel. The unidirectional cylinder products of our company mainly use rolling processing, because the surface layer has surface residual compressive stress, which helps to close the surface micro-cracks and hinder the expansion of erosion. Thus, the corrosion resistance of the surface can be improved, and the fatigue crack can be delayed or expanded, and the fatigue strength of the body can be improved. The correct rolling process of the unidirectional cylinder block: broaching block - fine boring block - grinding block. The rolling method is: broaching block - fine boring block - rolling block, the process is 3 parts, but the time is compared: grinding 1 meter of the block is about 1-2 days, rolling 1 meter of the block is about 10-30 minutes. Input comparison: grinding machine or quilting machine (tens of thousands - millions), rolling knife (ten thousand - tens of thousands). After rolling, the surface roughness of the hole decreases from RA3.2-6.3um before rolling to RA0.4-0.8&um, the surface hardness of the hole increases by about 30%, and the fatigue strength of the inner surface of the unidirectional cylinder increases by 25%. If the service life of the unidirectional cylinder is only considered, it is increased by 2 to 3 times, and the efficiency of the boring and rolling process is about 3 times higher than that of the grinding process. unidirectional cylinder misoperation or operation failure may be caused by the following reasons, you can start from these aspects of the investigation: (1) spool stuck or valve hole blocked. When the spool of the flow valve or direction valve is stuck or the valve hole is blocked, the unidirectional cylinder is prone to misoperation or operation failure. At this time, the contamination of the oil should be checked; Check whether dirt or colloidal deposits are stuck in the spool or blocking the valve hole; Check the wear of the valve body, clean and replace the system filter, clean the fuel tank, and replace the hydraulic medium. (2) The piston rod and unidirectional cylinder are stuck or the unidirectional cylinder is blocked. At this time, no matter how to manipulate, the unidirectional cylinder does not move or moves very little. At this time, check whether the piston and piston rod seal is too tight, whether it enters the dirt and gum deposits: whether the shaft line of the piston rod and the unidirectional cylinder is in the center, whether the wearing parts and seals are invalid, and whether the load is too large.

unidirectional cylinder and hydraulic station selection: Select the type and structure of the unidirectional cylinder according to the operation requirements of the main engine. According to the external load force borne by the unidirectional cylinder, such as gravity, friction force of the external mechanism, inertia force and working load, determine the load change law of the unidirectional cylinder in each stage of the stroke and the power value that must be provided. Determine the diameter of the piston and piston rod according to the working load of the unidirectional cylinder and the selected oil working pressure. the flow rate of the hydraulic pump is determined according to the movement speed of the unidirectional cylinder, the diameter of the piston and the piston rod.

unidirectional cylinder daily maintenance, should focus on checking whether the piston rod surface roughness and shape and position tolerance meet the technical requirements, if the piston rod bending should be calibrated to meet the requirements or according to the physical mapping, manufactured by a professional manufacturer. If the piston rod surface coating wear, slip damage, local spalling can be adopted to remove the coating, re-chrome surface processing process.

Answers to some questions about unidirectional cylinder:

What is the cause of sound and vibration when the hydraulic cylinder is under load?
The main reason 1) may be that the load machinery has stuck phenomenon, and the resistance is large. 2) The hydraulic oil is not enough, or the filter is blocked by dirty things, and the oil is flooded. 3) There is a problem with the pump.

How to calculate the inner diameter of the hydraulic cylinder?
These two parameters need the following information to decide: 1, pump displacement, speed (to get the actual output flow of the pump) 2, three and time requirements (lift time, drop time takes a few seconds) and then view the close cylinder series according to the results. Select the right cylinder.