stacker cylinder Sold to Puerto Rico

This article mainly introduces:

Puerto Rico hydraulic cylinder,stacker cylinder manufacturer,stacker cylinder

(Puerto Rico stacker cylinder,produced by Hengyu Group）

stacker cylinder are widely used in Puerto Rico，because of powerful torque，clever hydraulic energy conversion，simple structure and reliable operation.So our company has designed stacker cylinder for customers from Puerto Rico.

Introduction to stacker cylinder:

What kind of process is used in the stacker cylinder to make high-quality stacker cylinder products: the body is the main component of the stacker cylinder, mining single pillar, hydraulic support, gun tube and other products, and its processing quality directly affects the life and reliability of the entire product. Body processing requirements are high, the internal surface roughness requirements are Ra0.4 ~ 0.8&um, the coaxiality, wear resistance requirements are strict. The basic feature of body is deep hole processing, which has always troubled the processing personnel. The stacker cylinder products of our company mainly use rolling processing, because the surface layer has surface residual compressive stress, which helps to close the surface micro-cracks and hinder the expansion of erosion. Thus, the corrosion resistance of the surface can be improved, and the fatigue crack can be delayed or expanded, and the fatigue strength of the body can be improved. The correct rolling process of the stacker cylinder block: broaching block - fine boring block - grinding block. The rolling method is: broaching block - fine boring block - rolling block, the process is 3 parts, but the time is compared: grinding 1 meter of the block is about 1-2 days, rolling 1 meter of the block is about 10-30 minutes. Input comparison: grinding machine or quilting machine (tens of thousands - millions), rolling knife (ten thousand - tens of thousands). After rolling, the surface roughness of the hole decreases from RA3.2-6.3um before rolling to RA0.4-0.8&um, the surface hardness of the hole increases by about 30%, and the fatigue strength of the inner surface of the stacker cylinder increases by 25%. If the service life of the stacker cylinder is only considered, it is increased by 2 to 3 times, and the efficiency of the boring and rolling process is about 3 times higher than that of the grinding process. stacker cylinder misoperation or operation failure may be caused by the following reasons, you can start from these aspects of the investigation: (1) spool stuck or valve hole blocked. When the spool of the flow valve or direction valve is stuck or the valve hole is blocked, the stacker cylinder is prone to misoperation or operation failure. At this time, the contamination of the oil should be checked; Check whether dirt or colloidal deposits are stuck in the spool or blocking the valve hole; Check the wear of the valve body, clean and replace the system filter, clean the fuel tank, and replace the hydraulic medium. (2) The piston rod and stacker cylinder are stuck or the stacker cylinder is blocked. At this time, no matter how to manipulate, the stacker cylinder does not move or moves very little. At this time, check whether the piston and piston rod seal is too tight, whether it enters the dirt and gum deposits: whether the shaft line of the piston rod and the stacker cylinder is in the center, whether the wearing parts and seals are invalid, and whether the load is too large.

The wear of the hard chromium plating layer of the stacker cylinder is mostly caused by the grinding of the friction iron powder of the piston, and the wear is faster when there is water in the middle. Corrosion caused by the contact potential difference of the metal only occurs in the part of the piston contact, and the corrosion occurs in a point pattern. As mentioned above, when there is moisture in the middle, it will promote the development of corrosion. Compared with castings, the contact potential difference of copper alloy is higher, so the corrosion degree of copper alloy is more serious.

If the stacker cylinder piston rod is found to be worn, it can be brushed and plated first, then ground, and finally adjust the mating accuracy of the piston rod and the guide sleeve. At this time, the guide sleeve can be properly redrilled or the guide sleeve can be re-turned. When making the above repairs, remember to replace various rubber seals in time.

When installing the stacker cylinder pipe, the pipe should be cleaned after installation, and should not pass through the stacker cylinder block, and the by-pass pipe must be installed in front of the oil port of the stacker cylinder block. This is important. Otherwise, the foreign body in the pipeline will enter the stacker cylinder, and once it enters, it is difficult to exclude it, but it becomes a foreign body transported to the stacker cylinder. Moreover, when cleaning, the removal method of foreign bodies entered in the installation pipeline operation should be considered. In addition, the corrosion in the pipe should be pickling and other procedures before the pipe installation, and the rust must be completely removed.

Answers to some questions about stacker cylinder:

The inner diameter of the injection cylinder is 203.2mm and the diameter of the screw is 63.5mm. What is the enhancement ratio?
Oil pressure multiplied by the cross-sectional area of the cylinder is equal to the theoretical output force value, and then multiplied by the efficiency of the cylinder is equal to the actual output force value, and the oil pressure can be calculated by inverting the value input.

What is the material of the cylinder support ring?
Generally, it is polytetrafluoroethylene doped with copper powder, or polyformaldehyde, and copper sleeves, there are also nylon, resin and so on.