road paving machine hydraulic cylinder Sold to Chile

This article mainly introduces:

Chile hydraulic cylinder,road paving machine hydraulic cylinder manufacturer,road paving machine hydraulic cylinder

(Chile road paving machine hydraulic cylinder,produced by Hebei Hengyu company）

road paving machine hydraulic cylinder are widely used in Chile，because of no transmission clearance，powerful torque，clever hydraulic energy conversion.So our company has designed road paving machine hydraulic cylinder for customers from Chile.

Introduction to road paving machine hydraulic cylinder:

When the initial action of the road paving machine hydraulic cylinder is slow, please check the temperature of the hydraulic system, because in the case of low temperature, the viscosity of the hydraulic oil is large and the fluidity is poor, resulting in slow action of the road paving machine hydraulic cylinder. The improvement method is to replace the hydraulic oil with good viscosity temperature performance, and the oil temperature at low temperature can be increased by heater or heating by the machine itself, and the normal working oil temperature of the system should be maintained at about 40 ° C.

The "O" ring can be used as an auxiliary seal inside the road paving machine hydraulic cylinder, and the elastic force of the "O" ring makes the sealing slip ring close to the sealing surface, generating sealing pressure to achieve sealing. When the internal hydraulic pressure increases, the "O" ring will further deform and squeeze the slip ring, thereby increasing the sealing pressure and improving the sealing performance. The structure has the characteristics of low friction coefficient, good wear resistance, automatic compensation for wear and absorption of hard particles in the road paving machine hydraulic cylinder, and can be completely sealed.

1, the hydraulic machinery should be kept clean, in order to prevent dust and debris from falling into the oil, the tank should be sealed. 2, the oil in the tank should be replaced regularly according to the working condition. When changing the oil, the dirt and impurities accumulated at the bottom of the tank should be removed and the tank should be cleaned. 3, hydraulic oil, oil drums should be set in a clean and safe place to strengthen management. The oil drum, oil filter, oil funnel, oil pipe, etc. used should be kept clean. The oil drums for loading hydraulic oil must be cleaned in advance, and the oil drums should be dedicated and not mixed with other oil drums.

How to determine the working pressure of the road paving machine hydraulic cylinder: The pressure depends on the load size (i.e., F) and the type of equipment. The limitations of assembly space, economic conditions and component availability of the actuator should also be considered. In the case of a certain load, it is necessary to increase the structural size of the actuator if the working pressure is low, for some equipment, the size may be limited, and it is not economical from the point of view of material consumption; On the contrary, if the pressure selection is too high, the material, sealing and manufacturing accuracy of the pump, road paving machine hydraulic cylinder, valve and other components are also required to be high, which will inevitably increase the cost of equipment. In general, for equipment with a fixed size that is not too limited, the pressure can be selected lower, and the walking machinery should be selected higher.

Answers to some questions about road paving machine hydraulic cylinder:

Why hydraulic cylinder load can not rise?
The hydraulic cylinder does not top up indicates that the pressure of the working chamber of the hydraulic cylinder is insufficient, and the following circumstances can lead to insufficient pressure: 1) The relief valve of the hydraulic system cannot establish pressure, elimination method: check whether the pressure setting screw of the relief valve is screwed to the appropriate position. If it is an electromagnetic relief valve, please check the power-on condition. 2) The hydraulic system pipeline is connected incorrectly, when P and T are connected, this must be checked and excluded; 3) Excessive leakage in the hydraulic cylinder, resulting in (only for double-acting cylinders); 3) No hydraulic oil into the working chamber of the hydraulic cylinder, elimination method: first disassemble the hydraulic pipe connecting the reversing valve and the hydraulic cylinder, and then control the reversing valve, and observe whether there is hydraulic oil flowing out of the reversing valve.

What size of hydraulic cylinder is needed for 200 tons pressure? The pressure of the cylinder at work is determined by the load, and the pressure of the physical force is equal to the force divided by the area of action (that is, P=F/S). If you want to calculate the output force of the cylinder, you can calculate by the formula: Set the radius of the piston (that is, the cylinder) is R (unit mm) the radius of the piston rod is r (unit mm) the pressure level P (unit MPa) when working, then the thrust of the cylinder F push =3.14*R*R*P (unit N) the pull of the cylinder F pull =3.14* (R* R-R *R) *P (unit N) 100 tons of the cylinder, System pressure 16Mpa.