stacker cylinder Sold to Mexico

This article mainly introduces:

Mexico hydraulic cylinder,stacker cylinder manufacturer,stacker cylinder

(Mexico stacker cylinder,produced by Hengyu Group）

stacker cylinder are widely used in Mexico，because of powerful torque，clever hydraulic energy conversion，simple structure and reliable operation.So our company has designed stacker cylinder for customers from Mexico.

Introduction to stacker cylinder:

What kind of process is used in the stacker cylinder to make high-quality stacker cylinder products: the body is the main component of the stacker cylinder, mining single pillar, hydraulic support, gun tube and other products, and its processing quality directly affects the life and reliability of the entire product. Body processing requirements are high, the internal surface roughness requirements are Ra0.4 ~ 0.8&um, the coaxiality, wear resistance requirements are strict. The basic feature of body is deep hole processing, which has always troubled the processing personnel. The stacker cylinder products of our company mainly use rolling processing, because the surface layer has surface residual compressive stress, which helps to close the surface micro-cracks and hinder the expansion of erosion. Thus, the corrosion resistance of the surface can be improved, and the fatigue crack can be delayed or expanded, and the fatigue strength of the body can be improved. The correct rolling process of the stacker cylinder block: broaching block - fine boring block - grinding block. The rolling method is: broaching block - fine boring block - rolling block, the process is 3 parts, but the time is compared: grinding 1 meter of the block is about 1-2 days, rolling 1 meter of the block is about 10-30 minutes. Input comparison: grinding machine or quilting machine (tens of thousands - millions), rolling knife (ten thousand - tens of thousands). After rolling, the surface roughness of the hole decreases from RA3.2-6.3um before rolling to RA0.4-0.8&um, the surface hardness of the hole increases by about 30%, and the fatigue strength of the inner surface of the stacker cylinder increases by 25%. If the service life of the stacker cylinder is only considered, it is increased by 2 to 3 times, and the efficiency of the boring and rolling process is about 3 times higher than that of the grinding process. stacker cylinder misoperation or operation failure may be caused by the following reasons, you can start from these aspects of the investigation: (1) spool stuck or valve hole blocked. When the spool of the flow valve or direction valve is stuck or the valve hole is blocked, the stacker cylinder is prone to misoperation or operation failure. At this time, the contamination of the oil should be checked; Check whether dirt or colloidal deposits are stuck in the spool or blocking the valve hole; Check the wear of the valve body, clean and replace the system filter, clean the fuel tank, and replace the hydraulic medium. (2) The piston rod and stacker cylinder are stuck or the stacker cylinder is blocked. At this time, no matter how to manipulate, the stacker cylinder does not move or moves very little. At this time, check whether the piston and piston rod seal is too tight, whether it enters the dirt and gum deposits: whether the shaft line of the piston rod and the stacker cylinder is in the center, whether the wearing parts and seals are invalid, and whether the load is too large.

When the stacker cylinder is in use, once the seal and guide support ring are found to be defective, the seal with the same structural form and appropriate material should be replaced according to the structural form of the stacker cylinder seal to be repaired, so as to minimize the thickness of the oil film between the seal and the sealing surface and reduce the leakage of the seal.

stacker cylinder use should try to avoid sealing belt into the stacker cylinder. As a simple sealing material, polytetrafluoroethylene plastic sealing tape is often used in installation and inspection, and if the winding method of the linear and ribbon-shaped sealing material is wrong, the sealing tape will be cut off and enter the stacker cylinder. The wire belt seal will not have any effect on the winding of the sliding part, but it will cause the check valve of the stacker cylinder to fail to operate or the buffer regulating valve can not be adjusted to the end. For the circuit, it may cause the action of the reversing valve, the relief valve and the reducing valve to fail.

When installing the stacker cylinder pipe, the pipe should be cleaned after installation, and should not pass through the stacker cylinder block, and the by-pass pipe must be installed in front of the oil port of the stacker cylinder block. This is important. Otherwise, the foreign body in the pipeline will enter the stacker cylinder, and once it enters, it is difficult to exclude it, but it becomes a foreign body transported to the stacker cylinder. Moreover, when cleaning, the removal method of foreign bodies entered in the installation pipeline operation should be considered. In addition, the corrosion in the pipe should be pickling and other procedures before the pipe installation, and the rust must be completely removed.

Answers to some questions about stacker cylinder:

How does the hydraulic solenoid valve realize that the cylinder stops at any position?
Use an O-type medium function solenoid directional valve, or use a Y-type solenoid directional valve and a hydraulically controlled check valve.

Is there a national standard for the testing of hydraulic cylinders?
Generally speaking, the cylinder test is carried out according to JB/JQ20302 Allowable leakage of cylinder in pre-factory leakage test. GB2879 hydraulic cylinder piston and piston rod dynamic seal groove type, size and tolerance. GB6578 hydraulic cylinder piston rod dust ring groove type, size and tolerance. GB7938 hydraulic cylinder and cylinder nominal pressure series, etc.