non-standard special type cylinder Sold to Dominica

This article mainly introduces:

Dominica hydraulic cylinder,non-standard special type cylinder manufacturer,non-standard special type cylinder

(Dominica non-standard special type cylinder,produced by Hengyu Hydraulic Cylinder Factory）

non-standard special type cylinder are widely used in Dominica，because of high work efficiency，excellent fatigue and impact resistance，no need for deceleration device.So our company has designed non-standard special type cylinder for customers from Dominica.

Introduction to non-standard special type cylinder:

The advantages and disadvantages of the non-standard special type cylinder: the surface of the non-standard special type cylinder by painting, coating protection treatment, bright luster is not easy to rust, all raw materials of the non-standard special type cylinder through the top heat treatment, high manufacturing precision, belongs to the precision machinery, has a simple structure, stable quality, high mechanical efficiency, easy to achieve automation and many other advantages. However, hydraulic technology also has the shortcomings of oil leakage, oil temperature change affecting the control of running speed, noise, expensive cost and high maintenance cost.

non-standard special type cylinder piston rod material selection and requirements: ① piston rod is usually made of 45 steel. When there is a large impact force and heavy load transmission, it is made of 40Cr steel. This is to ensure that the piston rod has sufficient working strength. The piston rod is generally designed as a non-standard special type cylinder, if the diameter is larger, the hollow piston rod can be used. Made of No. 45 seamless steel pipe. ③ When the piston rod is manufactured, the blank should be first forged and conditioned after mechanical rough processing, and the hardness of HB=230 ~ 250. The purpose of conditioning is to improve the machining performance and increase the working strength of the material. ④ The surface roughness Ra of the piston rod after finishing should not be greater than 0.65μm. ⑤ In order to improve the corrosion resistance of the piston rod, the working surface of the rod can be plated with hard chromium. ⑥ The piston rod and the end cap are guided by H8 ' non-standard special type cylinder piston rod industry standard: piston rod diameter series of national recommended standard GB/T2348-1993. Piston rod thread size series standard GB/T2350-1980. Please refer to execute. There is no industry standard for piston rods Both the non-standard special type cylinder and the hydraulic motor are devices that convert the pressure energy of the liquid into mechanical energy and output it. The non-standard special type cylinder mainly outputs linear motion and force. The non-standard special type cylinder has a variety of forms, according to the different characteristics of its mechanism it can be divided into piston type, plunger type and swing type three categories, according to the mode of action he can be divided into single action and double action. Piston non-standard special type cylinder, plunger non-standard special type cylinder is mainly used for: machinery, such as excavators; Scientific research, such as university structure laboratory. The plunger non-standard special type cylinder is used for pressure testing machines, such as Jinan test, and the test machine is used for material testing.

The non-standard special type cylinder requires that the filtration accuracy of the system is not less than the 80um, and the oil pollution should be strictly controlled, the oil should be kept clean, the performance of the oil should be checked regularly, and the necessary fine filtration and replacement of new working oil should be carried out.

The "O" ring can be used as an auxiliary seal inside the non-standard special type cylinder, and the elastic force of the "O" ring makes the sealing slip ring close to the sealing surface, generating sealing pressure to achieve sealing. When the internal hydraulic pressure increases, the "O" ring will further deform and squeeze the slip ring, thereby increasing the sealing pressure and improving the sealing performance. The structure has the characteristics of low friction coefficient, good wear resistance, automatic compensation for wear and absorption of hard particles in the non-standard special type cylinder, and can be completely sealed.

Answers to some questions about non-standard special type cylinder:

When does the cylinder rotate?
The piston rod inside the multistage plunger cylinder can be rotated, and it will rotate when it is subjected to tangential force.

What is the cause of the sound of the excavator arm cylinder?
Hydraulic excavator cylinder includes boom cylinder, bucket rod cylinder and bucket cylinder, four cylinders. The sound of boom cylinder may be the wear of hydraulic cylinder block bushing, piston rod bushing and shaft pin. The main reason: poor lubrication, followed by improper clearance in the assembly process. Countermeasures: (1) Strictly lubricate each shaft pin at least once every 8 hours when the excavator is initially used for 100 hours and under harsh conditions; In other working conditions, lubricate each pin at least once every 50 hours. (2) If the lubricating oil passage is found to be blocked, it must be stopped for rectification. (3) Require assembly, replacement of all parts of the shaft pin, bushing strictly comply with the assembly testing standards and operating procedures.