electromagnetic induction cylinder Sold to Finland

This article mainly introduces:

Finland hydraulic cylinder,electromagnetic induction cylinder manufacturer,electromagnetic induction cylinder

(Finland electromagnetic induction cylinder,produced by Hebei Hengyu company）

electromagnetic induction cylinder are widely used in Finland，because of powerful torque，simple structure and reliable operation，clever hydraulic energy conversion.So our company has designed electromagnetic induction cylinder for customers from Finland.

Introduction to electromagnetic induction cylinder:

1, the hydraulic machinery should be kept clean, in order to prevent dust and debris from falling into the oil, the tank should be sealed. 2, the oil in the tank should be replaced regularly according to the working condition. When changing the oil, the dirt and impurities accumulated at the bottom of the tank should be removed and the tank should be cleaned. 3, hydraulic oil, oil drums should be set in a clean and safe place to strengthen management. The oil drum, oil filter, oil funnel, oil pipe, etc. used should be kept clean. The oil drums for loading hydraulic oil must be cleaned in advance, and the oil drums should be dedicated and not mixed with other oil drums.

The role of the electromagnetic induction cylinder in the mold industry: the electromagnetic induction cylinder has a variety of uses in the mold, one is that the core distance is very large, or because of the mechanism of the product, only the electromagnetic induction cylinder is reasonable or more cost saving. Let the side core be extracted before opening the mold. Hot runner is mainly based on the product to decide, sometimes customers require the use of hot runner, the price is more expensive, but there are many benefits, you can save raw materials, shorten the molding cycle The electromagnetic induction cylinder has an irreplaceable role in the heavy industry production process: it is mainly used in places that need to support heavy objects for a long time, and it can still support heavy objects when the oil pressure is removed, and it is safe and reliable. Can be used underwater, single action, load reversion, nut self-locking to make the load safer, especially in large projects, is easy to operate control and self-locking jack, designed with a safety pressure retaining device, built-in pressure relief valve to prevent overload, to protect the self-locking jack to facilitate safe operation. The connection of the device is connected by high pressure hose and threaded joint, which has the advantages of fast use and overcoming the shortcomings of fast traditional joint oil leakage. It is mainly used for equipment installation and toppling operation in various industries such as electric power, construction, machinery manufacturing, mining, railway bridge, shipbuilding and so on.

Causes and countermeasures of oil electromagnetic induction cylinder leakage: Cast iron ring seal allows a certain degree of internal leakage. The impurities in the electromagnetic induction cylinder will lead to premature wear of the piston seal, replace the piston seal; If the electromagnetic induction cylinder is visibly scarred, the electromagnetic induction cylinder must be replaced. It can be pressurized at one end of the electromagnetic induction cylinder and opened at the other end of the oil port to observe whether there is obvious internal leakage at the end of the oil port. Most electromagnetic induction cylinder piston drift may not come from the electromagnetic induction cylinder, the above method to determine the electromagnetic induction cylinder without internal leakage is helpful to determine the problem of the hydraulic system related components.

electromagnetic induction cylinder hydraulic oil selection: The recommended working oil viscosity of the electromagnetic induction cylinder is 10 ~ 110cSt (1.8 ~ 15E), ISO VG46 hydraulic oil. The normal working oil temperature is 10 ~ 70℃, and the ambient temperature is in the range of -20 ~ 80℃. When the ambient temperature and service temperature are low, the hydraulic oil with lower viscosity can be selected.

Answers to some questions about electromagnetic induction cylinder:

How to deal with the surface degreasing process before spraying paint after cylinder assembly, and what degreasing agent is used?
Cylinder painting, generally using the following process (note: the cylinder is best painted, do not spray powder coating, because the powder coating curing temperature is high, will lead to sealing defects and oil leakage) : Pre-degreasing - degreasing - washing - washing - pickling - washing - washing - table adjustment - phosphating - washing - washing - drying - polishing - spray primer - spray paint degreasing agent generally use neutral or weak alkaline degreasing agent, phosphating liquid generally use zinc phosphating liquid.

Can pneumatic cylinder be used as hydraulic cylinder?
The pneumatic cylinder can only be used for pressure below 1MPA, and if it is used for hydraulic, the pressure should be under 1MPA, which may not meet the strength requirements. And the seals should use fluorine rubber to avoid corrosion. But pneumatic cylinder used as hydraulic cylinder is not whimsical, in fact, there is such a use. The pneumatic system has a natural defect, that is, the speed is unstable, especially in the case of low speed. The hydraulic pressure is very stable, if you do not want to buy a set of hydraulic system, while the strength of the cylinder is not large, you can use compressed air to push the hydraulic oil, with hydraulic oil to drive the cylinder, The force is the same as compressed air, but very smooth.