High quality hydraulic equipment manufacturers!
TELL:+8613184968882

100 ton hydraulic cylinder Sold to Turkmenistan

Release time:2023-11-12 15:33:17 Hits: Current position: Home > News

This article mainly introduces:

Turkmenistan hydraulic cylinder,100 ton hydraulic cylinder manufacturer,100 ton hydraulic cylinder

Turkmenistan 100 ton hydraulic cylinder

(Turkmenistan 100 ton hydraulic cylinder,produced by Hengyu Group)

100 ton hydraulic cylinder are widely used in Turkmenistan,because of no need for deceleration device,high work efficiency,long service life.So our company has designed 100 ton hydraulic cylinder for customers from Turkmenistan.

Introduction to 100 ton hydraulic cylinder:

When the 100 ton hydraulic cylinder is repaired, its inner and outer diameter and roundness should be accurately measured. If the inner hole of the 100 ton hydraulic cylinder is badly worn, it can be repaired by grinding the mandrel or honing on the boring machine. If the piston is worn, it can be repaired by electroplating, and serious wear should be replaced.

We can not just consider the price and ignore the quality when we purchase the 100 ton hydraulic cylinders. Now some manufacturers produce unqualified products in order to reduce costs, the piston rod is not adjusted, the rod coating is not enough, the 100 ton hydraulic cylinder finish can not reach, the guide sleeve should use copper, but instead of ductile iron, although the cost is reduced, the quality of the 100 ton hydraulic cylinder is not required.

Causes and countermeasures of oil 100 ton hydraulic cylinder leakage: Cast iron ring seal allows a certain degree of internal leakage. The impurities in the 100 ton hydraulic cylinder will lead to premature wear of the piston seal, replace the piston seal; If the 100 ton hydraulic cylinder is visibly scarred, the 100 ton hydraulic cylinder must be replaced. It can be pressurized at one end of the 100 ton hydraulic cylinder and opened at the other end of the oil port to observe whether there is obvious internal leakage at the end of the oil port. Most 100 ton hydraulic cylinder piston drift may not come from the 100 ton hydraulic cylinder, the above method to determine the 100 ton hydraulic cylinder without internal leakage is helpful to determine the problem of the hydraulic system related components.

If the 100 ton hydraulic cylinder is sliding or crawling (stop and go), check whether there is any astringency inside the 100 ton hydraulic cylinder. The internal parts of the 100 ton hydraulic cylinder are improperly assembled, the parts are deformed, worn or the shape and position tolerance is excessive, and the action resistance is too large, so that the piston speed of the 100 ton hydraulic cylinder changes with the different stroke position, and there is slip or crawl. Most of the reasons are due to poor assembly quality of parts, surface scars or sintered iron filings, so that the resistance increases, the speed decreases. For example, the piston is different from the piston rod or the piston rod is bent, the 100 ton hydraulic cylinder or the piston rod is offset from the mounting position of the guide rail, and the sealing ring is too tight or too loose. The solution is to repair or adjust, replace damaged parts and remove iron filings. At the same time, check whether the lubrication is good or whether the 100 ton hydraulic cylinder bore processing is out of whack. Because the piston and 100 ton hydraulic cylinder, guide rail and piston rod are relative If the 100 ton hydraulic cylinder is crawling seriously, check whether air has entered the hydraulic system. Air compression or expansion can cause the piston to slip or crawl. The exclusion measures are to check the hydraulic pump, set up a special exhaust device, and quickly operate the exhaust several times in the full stroke. Check the seals at the same time, because the quality of the seals is directly related to slippage or crawling. When the O-ring is used under low pressure, compared with the U-ring, it is easy to slip or crawl because of the higher surface pressure and the larger difference between static and static friction resistance. The surface pressure of the U-shaped sealing ring increases with the increase of pressure, although the sealing effect is correspondingly improved, but the difference between static and static friction resistance is also larger, the internal pressure increases, affecting the rubber elasticity, due to the increase in the contact resistance of the lip, the sealing ring will tip over and the lip elongation, and it is also easy to cause slip or crawling 100 ton hydraulic cylinder weight composition and calculation. The weight of the 100 ton hydraulic cylinder is composed of the 100 ton hydraulic cylinder diameter, the outer diameter and weight of the 100 ton hydraulic cylinder, the rod diameter, and the weight of the accessories, so in calculation, it is to add all these together to get the specific value. However, if there are special circumstances, it may be calculated separately. This work can be carried out by yourself, but it can also be carried out by professionals, so that mistakes can be avoided.

Answers to some questions about 100 ton hydraulic cylinder:

What is the HS code of the hydraulic cylinder?
HS code of hydraulic cylinder; 8412210000 8412210000 Linear hydraulic power unit (hydraulic cylinder) 0.12000 0.35000 0.00000 0.17000 0.00000

What size of hydraulic cylinder is needed for 200 tons pressure? The pressure of the cylinder at work is determined by the load, and the pressure of the physical force is equal to the force divided by the area of action (that is, P=F/S). If you want to calculate the output force of the cylinder, you can calculate by the formula: Set the radius of the piston (that is, the cylinder) is R (unit mm) the radius of the piston rod is r (unit mm) the pressure level P (unit MPa) when working, then the thrust of the cylinder F push =3.14*R*R*P (unit N) the pull of the cylinder F pull =3.14* (R* R-R *R) *P (unit N) 100 tons of the cylinder, System pressure 16Mpa.

Back to list Recommended article

Leave a message if you have any questions.

Send
Email

Email:hsslrubbertech@gmail.com7x24 hours

Glad to receive your consultation!:

Service
Tel

+8613184968882
7x24hours service

Add
Wechat

Add Wechat
TOP