tailplate hydraulic cylinder Sold to Cote d 'Ivoire

This article mainly introduces:

Cote d 'Ivoire hydraulic cylinder,tailplate hydraulic cylinder manufacturer,tailplate hydraulic cylinder

(Cote d 'Ivoire tailplate hydraulic cylinder,produced by Hengyu Group）

tailplate hydraulic cylinder are widely used in Cote d 'Ivoire，because of long service life，excellent fatigue and impact resistance，no need for deceleration device.So our company has designed tailplate hydraulic cylinder for customers from Cote d 'Ivoire.

Introduction to tailplate hydraulic cylinder:

Regular maintenance of the tailplate hydraulic cylinder includes: regular tightening, tailplate hydraulic cylinder fastening screws and gland screws, tailplate hydraulic cylinder piston rod stop adjustment screws, should be tightened once a month, tighten each screw evenly, and achieve the corresponding tightening torque. Replace the seal regularly, it is recommended to replace the seal of the tailplate hydraulic cylinder once a year. Clean regularly, the tailplate hydraulic cylinder is cleaned every other year, and the seals are replaced while cleaning.

tailplate hydraulic cylinder piston sealing is best to use Yx ring, polyurethane and polytetrafluoroethylene sealing material combination, can significantly improve the sealing performance: (I), reduce friction resistance, no crawling phenomenon; (ii) Have good dynamic and static sealing, wear resistance, long service life; (iii) The installation groove is simple, and the disassembly is simple.

The tailplate hydraulic cylinder should be avoided for a long time without use, if it is indeed idle for a long time for some reason, it should also be regularly turned on for empty operation, so that its parts can be fully lubricated, so as to avoid rust on the working surface and affect the normal work in the future. (If it cannot be turned on and run, a small amount of lubricating oil can be applied on its outer surface for protection) ' The use of the tailplate hydraulic cylinder should pay attention to: the operation should be as far away from the tailplate hydraulic cylinder as possible, to avoid falling objects, knocking, rubbing the tailplate hydraulic cylinder coating. When cleaning the tailplate hydraulic cylinder, only use soft materials (such as cotton) to wipe, and do not scratch high-hardness materials. Do not use the tailplate hydraulic cylinder when the oil temperature exceeds 70 ° C.

The pressure, temperature, medium and speed of different types of seals are not the same, water-ethylene glycol medium (HFC) can not be sealed with polyurethane, it can only use rubber seal; When the tailplate hydraulic cylinder is running fast, it must be sealed with slip ring, such as Sterseal, Glairing, GD1000K, TDI, etc., when the running speed is slow, Yx, U, V combination seals can be used; Fluorine rubber seal is used in high temperature and high pressure environment; When the running speed is fast, the buffer sleeve and buffer valve must be considered.

Answers to some questions about tailplate hydraulic cylinder:

What is the relationship between medium cylinder and side cylinder ratio of forklift truck?
The middle cylinder and the side cylinder seem to have no relationship, as long as the lifting speed required by the design can be ensured, but the diameter of the cylinder can not be too thin, so as to avoid the middle cylinder acting first when the high gantry vibration lifting, and then the two cylinders acting again.

What type of seal is the cylinder of shaft 50?
You won't know the exact model until you take it apart. Oil seals have O, Y, Yx, KYx, U, UN, UHS, YA, St, Gray, Yamagata, Lei type, etc. It is difficult to know what kind of oil seal the designer chooses. Cylinder oil seal installation method: 1. Receive a fixed number of oil seals. 2. From receiving the oil seal to assembly, it must be kept clean. 3. Before assembly, check the oil seal and measure whether the size of each part of the oil seal is consistent with the size of the shaft and cavity. Before the oil seal is installed, the size of the shaft diameter should be clearly compared with the inner diameter of the oil seal. The inner cavity size should be suitable for the outer diameter width of the oil seal. Check the lip of the oil seal for damage.