spring return cylinder Sold to Tunisia

This article mainly introduces:

Tunisia hydraulic cylinder,spring return cylinder manufacturer,spring return cylinder

(Tunisia spring return cylinder,produced by Hengyu Hydraulic Co., Ltd）

spring return cylinder are widely used in Tunisia，because of high work efficiency，excellent fatigue and impact resistance，no need for deceleration device.So our company has designed spring return cylinder for customers from Tunisia.

Introduction to spring return cylinder:

Improve the service life of the spring return cylinder: it is necessary to maintain the normal clearance of the combined surface of the hydraulic components. When manufacturing or repairing the main parts of the spring return cylinder (such as the spring return cylinder block, piston rod, etc.), the assembly should be carried out in accordance with the tolerance lower limit of the assembly size, which can well reduce the occurrence of cavitation. If cavitation has occurred in the hydraulic components, only metallographic sandpaper polishing technology can be used to remove cavitation pitting and surface carbon deposits, and general fine sandpaper must not be used for polishing After the spring return cylinder is repaired, the hydraulic system should run smoothly for a certain period of time so that the hydraulic oil in the hydraulic system can be fully circulated; If necessary, the spring return cylinder inlet pipe (or return pipe) can be disassembled. Make the hydraulic oil overflow to achieve the effect of single spring return cylinder exhaust.

In order to ensure the service life of the spring return cylinder, the medium used must not be mixed with impurities and stolen goods, so as to avoid scratching the inner arm of the spring return cylinder, causing damage to the seal and causing leakage in the spring return cylinder. It is required that the filtration accuracy of the system is not less than 80μm, the oil pollution is strictly controlled, the hydraulic oil is kept clean, the performance of the hydraulic oil is regularly checked, and the necessary fine filtration or replacement of the new working hydraulic oil is carried out.

Because of the slightly complex structure of the buffer spring return cylinder, sometimes there will be problems, such as when the spring return cylinder with the buffer device is started in reverse, the piston often stops temporarily or reverses. Elimination method: The orifice of the check valve is too small, so that the amount of oil entering the buffer chamber is too small, and even a vacuum occurs, so the above fault phenomenon will occur when the buffer plunger leaves the end cover. In this regard, the orifice of the check valve should be increased.

When the spring return cylinder needs to be stored for a period of time, please follow the recommended methods: The spring return cylinder should be stored in a dry, clean, non-corrosive gas indoor environment, pay attention to protect the spring return cylinder from internal corrosion and external damage. If the indoor requirements cannot be met, the hardened and well-drained ground should be cushioned at least 30cm, and the upper part should be covered with waterproof storage. The oil spring return cylinder should not be in direct contact with water vapor for a long time. The spring return cylinder should be placed as vertically as possible with the piston rod facing up, which minimizes corrosion due to possible condensation in the spring return cylinder and permanent deformation of the seal due to the piston and rod weight. (When the shield is stored in the shield machine, the support shoe is placed upward). Keep the oil port protective cover until the pipe is connected. For long-term storage, the protection should be added on both sides of the piston of the spring return cylinder Before working, the spring return cylinder must be run repeatedly with low pressure (greater than the starting pressure) to discharge the air in the spring return cylinder before normal work. The oil inlet and outlet and the joint must be tightly fastened with a combination pad to prevent oil leakage.

Answers to some questions about spring return cylinder:

What material is the piston rod of the cylinder made of?
About the piston rod: ① Piston rods are usually made of 45# steel. When there is a large impact force and heavy load transmission, it is made of 40Cr steel. This is to ensure that the piston rod has sufficient working strength. ② The piston rod is generally designed as a cylinder, if the diameter is larger, the hollow piston rod can be used with 45# seamless steel pipe. ③ When the piston rod is manufactured, the blank should be first forged and conditioned after mechanical rough processing, and the hardness of HB=230 ~ 250. The purpose of conditioning is to improve the machining performance and increase the working strength of the material. ④ The surface roughness Ra of the piston rod after finishing should not be greater than 0.65μm. ⑤ In order to improve the corrosion resistance of the piston rod, the rod surface needs to be chrome plated.

What is the reason for the hydraulic cylinder sticking out and not retracting?
There are two reasons: First, the problem with the seal, if there are two seals on the piston, the top seal is broken. Second, when the hydraulic pressure itself is designed, the rod cavity area is too small, so that the desired return force can not be achieved during the return trip. You can first check whether the coupling is damaged; Then see if the relief valve in the oil line block is blocked. If the use time is too long, it needs to be cleaned, the hydraulic oil is very dirty and can block oil block. Electromagnetic directional valves can also be checked, but the chance of problems is relatively small, unless there is a product problem.