spring return cylinder Sold to Canada

This article mainly introduces:

Canada hydraulic cylinder,spring return cylinder manufacturer,spring return cylinder

(Canada spring return cylinder,produced by Hengyu Hydraulic Cylinder Factory）

spring return cylinder are widely used in Canada，because of long service life，smooth movement，high work efficiency.So our company has designed spring return cylinder for customers from Canada.

Introduction to spring return cylinder:

What kind of process is used in the spring return cylinder to make high-quality spring return cylinder products: the body is the main component of the spring return cylinder, mining single pillar, hydraulic support, gun tube and other products, and its processing quality directly affects the life and reliability of the entire product. Body processing requirements are high, the internal surface roughness requirements are Ra0.4 ~ 0.8&um, the coaxiality, wear resistance requirements are strict. The basic feature of body is deep hole processing, which has always troubled the processing personnel. The spring return cylinder products of our company mainly use rolling processing, because the surface layer has surface residual compressive stress, which helps to close the surface micro-cracks and hinder the expansion of erosion. Thus, the corrosion resistance of the surface can be improved, and the fatigue crack can be delayed or expanded, and the fatigue strength of the body can be improved. The correct rolling process of the spring return cylinder block: broaching block - fine boring block - grinding block. The rolling method is: broaching block - fine boring block - rolling block, the process is 3 parts, but the time is compared: grinding 1 meter of the block is about 1-2 days, rolling 1 meter of the block is about 10-30 minutes. Input comparison: grinding machine or quilting machine (tens of thousands - millions), rolling knife (ten thousand - tens of thousands). After rolling, the surface roughness of the hole decreases from RA3.2-6.3um before rolling to RA0.4-0.8&um, the surface hardness of the hole increases by about 30%, and the fatigue strength of the inner surface of the spring return cylinder increases by 25%. If the service life of the spring return cylinder is only considered, it is increased by 2 to 3 times, and the efficiency of the boring and rolling process is about 3 times higher than that of the grinding process. spring return cylinder misoperation or operation failure may be caused by the following reasons, you can start from these aspects of the investigation: (1) spool stuck or valve hole blocked. When the spool of the flow valve or direction valve is stuck or the valve hole is blocked, the spring return cylinder is prone to misoperation or operation failure. At this time, the contamination of the oil should be checked; Check whether dirt or colloidal deposits are stuck in the spool or blocking the valve hole; Check the wear of the valve body, clean and replace the system filter, clean the fuel tank, and replace the hydraulic medium. (2) The piston rod and spring return cylinder are stuck or the spring return cylinder is blocked. At this time, no matter how to manipulate, the spring return cylinder does not move or moves very little. At this time, check whether the piston and piston rod seal is too tight, whether it enters the dirt and gum deposits: whether the shaft line of the piston rod and the spring return cylinder is in the center, whether the wearing parts and seals are invalid, and whether the load is too large.

The spring return cylinder should be vented: when the spring return cylinder is installed or parked for a long time to work again, the air will penetrate into the spring return cylinder and the pipeline system. In order to prevent the abnormal phenomenon of crawling, noise and heating of the actuator, the air in the spring return cylinder and the system should be discharged. In order to facilitate the removal of air deposited in the spring return cylinder, the oil is best entered and discharged from the highest point of the spring return cylinder. spring return cylinders that require higher motion stability are often equipped with exhaust plugs at both ends. Before working, unscrew the exhaust plug to make the piston go back and forth several times without load in the whole stroke, and the air can be discharged through the exhaust plug. After the air is drained, tighten the exhaust plug before working.

When the control pressure of the hydraulic system is too low, the spring return cylinder will appear wrong or no action, because the throttle resistance in the control pipeline may be too large, the flow valve is improperly adjusted, the control pressure is inappropriate, and the pressure source is interfered with. At this time, check the control pressure source to ensure that the pressure is adjusted to the specified value of the system.

The material, shape and compression of the spring return cylinder seal have a great impact on the service life and work efficiency of the spring return cylinder. In addition to requiring a reliable seal, it should also have a long service life and less friction loss. At present, there are many seal manufacturers in the country, and it is also crucial to choose high-quality seals with reliable and stable quality.

Answers to some questions about spring return cylinder:

How to calculate hydraulic cylinder thrust?
Cylinder diameter = piston diameter =200MM Piston area =π (200/2) square =3140 square mm =31.4 square cm 25MPA=250KG/ square cm Maximum thrust = pressure * Piston area =250 *31.4 =7850KG=78500 Newtons This is the maximum thrust. The formula can be derived from the calculation formula.

How to determine the rated working pressure of the hydraulic cylinder?
Under normal circumstances, the working pressure is determined according to the size of the load and the installation space (the allowable diameter of the cylinder). In some special occasions, the smaller the cylinder, the better, the pressure level must be increased. The cylinder pressure is related to the estimated cost. The higher the pressure, the thicker the wall, the higher the cost, but conversely, the lower the pressure, the larger the diameter of the cylinder (when the same thrust) is required, the same high cost. Therefore, the rated pressure of the cylinder is concentrated in about 35 mpa, taking into account the cylinder diameter and wall thickness.