ejector cylinder Sold to Cameroon

This article mainly introduces:

Cameroon hydraulic cylinder,ejector cylinder manufacturer,ejector cylinder

(Cameroon ejector cylinder,produced by Hengyu Group）

ejector cylinder are widely used in Cameroon，because of excellent temperature resistance，no transmission clearance，powerful torque.So our company has designed ejector cylinder for customers from Cameroon.

Introduction to ejector cylinder:

ejector cylinder piston rod material selection and technical requirements: (I), because there is no special requirements, so use 45 steel as the piston rod material, the design of the piston rod only withstand pressure stress, so no modulation processing; (ii) The coaxial tolerance of the shaft journal and the outer circle of the mounting piston is not greater than 0.01mm, so as to ensure the coaxial degree of the outer circle of the piston rod and the outer circle of the piston, and avoid the stuck phenomenon of the piston and the ejector cylinder, the piston rod and the guide. The vertical tolerance between the end face of the mounting piston and the axis of the piston rod is not more than 0.04mm/100mm to ensure that the piston installation does not produce skew; (iii) The outer circle of the piston rod should pay attention to the roughness; (iv) Because it is operated under low load conditions, surface treatment is omitted.

When the ejector cylinder is customized, if there are high requirements for the quality of the ejector cylinder, it is best to use rolling processing, because the surface layer has surface residual compressive stress, which helps to close the surface of the small crack, preventing the expansion of erosion. Thus, the corrosion resistance of the surface can be improved, and the fatigue crack can be delayed or expanded, and the fatigue strength of the ejector cylinder can be improved. By rolling forming, a cold working hardening layer is formed on the rolling surface, which reduces the elastic and plastic deformation of the contact surface of the grinding pair, thereby improving the wear resistance of the inner wall of the ejector cylinder and avoiding the burn caused by grinding. After rolling, the reduction of surface roughness value can improve the matching property.

When the oil pressure of the ejector cylinder inlet is too low to reach the specified value, the leakage situation of the relevant oil system should be checked and the leakage should be eliminated; Check the piston and piston rod seal ring for damage, aging, loose and other phenomena; Check whether the hydraulic pump and pressure valve are faulty.

ejector cylinder abnormal sound, hysteresis phenomenon cause and elimination method: the piston rod is extended with abnormal sound and hysteresis, if the ejector cylinder is placed for a period of time, the ejector cylinder may enter the air, and the movement can be normal after dozens of repeated movements. If it still cannot be eliminated, check whether the load is aligned with the axis of the piston rod; Retracted piston rod installation helps to align the load with the piston rod. If the flow is unstable, it will also lead to abnormal movement of the piston rod. Check the relevant components of the hydraulic system.

Answers to some questions about ejector cylinder:

How big is the 100t cylinder pump and how big is the motor?
Load is calculated at 15 tons, stroke is calculated at 100 (both take the maximum) 15 tons = 15,000 kg, 15,000/210 bar (21 mpa) =71.42 square centimeters (cylinder area) 71.42/3,14 In the root *2=90,5 the inner diameter of the cylinder can be taken 100 mm. Travel 100 cm, that is, one meter, assuming 10, seconds a back and forth, then it is six times a minute, six meters per minute, then the required flow is,71,42*600 cm (6 meters) =42840 mm =42.84 liters/minute 42.84*21/60=14.9 kilowatts can choose 1450 RPM 4-stage motor 15KW.

Need to buy a hydraulic cylinder, now only know that the pressure needs to be between 20t and 50t. Two-way travel, how to determine the type of cylinder?
Important parameters of the cylinder: cylinder diameter, stroke, use pressure. First, the system pressure must be determined according to the precision of the operation of the application equipment, and the cylinder diameter can be determined by the force and system pressure. Then, according to how the equipment and the cylinder are installed and connected, determine the installation method of the cylinder and then determine the specific installation size, the size of the oil port, whether the buffer is needed and other details.