High quality hydraulic equipment manufacturers!
TELL:+8613184968882

self-locking hydraulic cylinder Sold to Burma

Release time:2023-12-11 09:05:27 Hits: Current position: Home > News

This article mainly introduces:

Burma hydraulic cylinder,self-locking hydraulic cylinder manufacturer,self-locking hydraulic cylinder

Burma self-locking hydraulic cylinder

(Burma self-locking hydraulic cylinder,produced by Hengyu Group)

self-locking hydraulic cylinder are widely used in Burma,because of simple structure and reliable operation,no transmission clearance,excellent temperature resistance.So our company has designed self-locking hydraulic cylinder for customers from Burma.

Introduction to self-locking hydraulic cylinder:

self-locking hydraulic cylinder and hydraulic station selection: Select the type and structure of the self-locking hydraulic cylinder according to the operation requirements of the main engine. According to the external load force borne by the self-locking hydraulic cylinder, such as gravity, friction force of the external mechanism, inertia force and working load, determine the load change law of the self-locking hydraulic cylinder in each stage of the stroke and the power value that must be provided. Determine the diameter of the piston and piston rod according to the working load of the self-locking hydraulic cylinder and the selected oil working pressure. the flow rate of the hydraulic pump is determined according to the movement speed of the self-locking hydraulic cylinder, the diameter of the piston and the piston rod.

self-locking hydraulic cylinder body inspection: The inner surface of the self-locking hydraulic cylinder and the piston seal are the main factors causing the leakage in the self-locking hydraulic cylinder, if the self-locking hydraulic cylinder has a longitudinal tensile mark, even if the new piston seal is replaced, it can not effectively eliminate the fault, the inner surface of the self-locking hydraulic cylinder mainly checks whether the dimensional tolerance and shape and position tolerance meet the technical requirements, there is no longitudinal tensile mark, and measures the depth of the longitudinal tensile mark, in order to take the corresponding solution.

In recent years, the processing process of the self-locking hydraulic cylinder generally adopts the rolling method, which is a pressure finishing processing, which uses the cold plastic characteristics of the metal at room temperature, and uses the rolling tool to exert a certain pressure on the surface of the workpiece, so that the surface metal of the workpiece produces plastic flow, and fills in the low concave trough of the original residue, and the roughness value of the workpiece surface is reduced. Due to the plastic deformation of the rolled surface metal, the surface tissue is cold hardened and the grain is fine, forming a dense fiber, and forming a residual stress layer, and the hardness and strength are increased, thus improving the wear resistance, corrosion resistance and compatibility of the workpiece surface. Rolling is a plastic machining method without cutting.

When the self-locking hydraulic cylinder is in use, once the seal and guide support ring are found to be defective, the seal with the same structural form and appropriate material should be replaced according to the structural form of the self-locking hydraulic cylinder seal to be repaired, so as to minimize the thickness of the oil film between the seal and the sealing surface and reduce the leakage of the seal.

Answers to some questions about self-locking hydraulic cylinder:

How to calculate hydraulic cylinder flow?
Effective area of the cylinder x stroke = volume usually in liters. Volume/estimated total travel time (converted to minutes) = oil flow rate.

What is the meaning of dead volume in hydraulic cylinder?
Closed volume, also known as dead zone volume Positive displacement pump is dependent on the change of sealing working volume to achieve suction and pressure oil, in order not to make the suction and pressure oil cavity interworking, there is an oil sealing area between the suction and pressure oil cavity, when the sealing working volume passes through the oil sealing area, neither pressure oil cavity nor oil suction cavity communication, forming a closed sealing volume. The unloading groove is opened, and the grooving principle is that the sealing volume decreases and the oil pressure chamber is communicated, and the sealing volume increases and the oil suction chamber is communicated.

Back to list Recommended article

Leave a message if you have any questions.

Send
Email

Email:hsslrubbertech@gmail.com7x24 hours

Glad to receive your consultation!:

Service
Tel

+8613184968882
7x24hours service

Add
Wechat

Add Wechat
TOP