steering cylinder Sold to Algeria

This article mainly introduces:

Algeria hydraulic cylinder,steering cylinder manufacturer,steering cylinder

(Algeria steering cylinder,produced by Hengyu Hydraulic Co., Ltd）

steering cylinder are widely used in Algeria，because of long service life，smooth movement，high work efficiency.So our company has designed steering cylinder for customers from Algeria.

Introduction to steering cylinder:

In the hydraulic system, sometimes the inner layer of the rubber hose is peeled off, so that the oil circuit is on and off, resulting in irregular steering cylinder action. Troubleshooting method: Replace the rubber hose.

If the steering cylinder operation failure, you can start from these aspects to troubleshoot: (1) the hydraulic system control pressure is too low. The throttling resistance in the control line may be too large, the flow valve is improperly adjusted, the control pressure is inappropriate, and the pressure source is disturbed. At this time, the control pressure source should be checked to ensure that the pressure is adjusted to the specified value of the system; (2) Air enters the hydraulic system. Mainly because there is a leak in the system. At this time, check the liquid level of the hydraulic tank, the seals and fittings on the oil suction side of the hydraulic pump, and whether the oil suction filter is too dirty. If so, the hydraulic oil should be replenished, seals and fittings should be treated, and the coarse filter element should be cleaned or replaced. (3) The initial action of the steering cylinder is slow. In the case of low temperature, the hydraulic oil viscosity is large, poor flow, resulting in slow steering cylinder action. The improvement method is to replace the hydraulic oil with better viscosity and temperature performance If the steering cylinder is weak and cannot push the load, please check the internal leakage problem. The internal leakage of the steering cylinder includes the leakage caused by excessive wear of the steering cylinder block seal, the piston rod and the seal cover seal and the piston seal. The cause of sealing leakage between the piston rod and the seal cover is that the seal is wrinkled, squeezed, torn, worn, aging, deterioration, deformation, etc., and a new seal should be replaced at this time. The main cause of excessive piston seal wear is improper adjustment of the speed control valve, resulting in excessive back pressure and improper seal installation or hydraulic oil contamination. The second is that foreign bodies enter the assembly and the quality of sealing materials is not good. The result is that the action is slow and weak, and in serious cases, it will cause damage to the piston and steering cylinder, and the phenomenon of "pulling the steering cylinder" appears. The treatment method is to adjust the speed control valve, and the necessary operations should be done according to the installation instructions.

In the process of using the steering cylinder, sometimes such a problem will occur, the steering cylinder can not act immediately after the instruction of the steering cylinder action is issued, and it must be moved after a short time, or sometimes it can move and stop moving, showing that the operation is very irregular. The cause and elimination of this failure mainly include air in the oil steering cylinder. Elimination method: exhaust through the exhaust valve. Check the piston rod reciprocating parts of the sealing ring for air inhalation, if so, replace the sealing ring.

The internal leakage of the steering cylinder is an important indicator to measure the quality of the steering cylinder: the internal leakage of the steering cylinder will reduce the volumetric efficiency, increase the temperature rise of the oil, affect the positioning accuracy of the steering cylinder, so that the steering cylinder can not accurately and stably stop in a certain position of the steering cylinder, so it is one of the main indicators of the steering cylinder.

Answers to some questions about steering cylinder:

Servo cylinder control principle
The electro-hydraulic pulse servo cylinder is composed of a stepper motor, a three-position four-way servo valve, a mechanical feedback device (a wire carrier) and an oil lever. When the stepper motor gets a pulse signal, its output shaft rotates 1.5 or 3 degrees, the servo valve spool drives the wire to rotate at the same time, the valve spool moves and opens the reversing cylinder to output pressure oil, the piston moves and drives the lead screw to reverse rotate the valve spool back to the original position, and the servo valve stops output pressure oil in the center. At this time, the cylinder moves 0.1 or 0.2mm stroke, and the displacement and speed of the cylinder travel are determined according to the given value of the electrical pulse.

Can the hydraulic oil in the cylinder return to the tank?
Yes, there is a way, for example, first remove the cylinder from the machine, and then connect the two pipes on the cylinder, so that the cylinder piston rod is completely retracted into the cylinder, at this time, the piston is with the bottom, and the rear chamber is almost no oil, and then screw off the joint at the end of the front chamber by the hydraulic station, and put it in an empty bucket. Finally, insert the gas pipe into the oil port of the rear chamber. Open the air source, and then the rod will run out, and you'll drain the hydraulic oil from the end of the rod, which requires a source of air on site.