track steering cylinder Sold to Algeria

This article mainly introduces:

Algeria hydraulic cylinder,track steering cylinder manufacturer,track steering cylinder

(Algeria track steering cylinder,produced by Hengyu Hydraulic Co., Ltd）

track steering cylinder are widely used in Algeria，because of long service life，smooth movement，high work efficiency.So our company has designed track steering cylinder for customers from Algeria.

Introduction to track steering cylinder:

The track steering cylinder should be used as far as possible to avoid the transverse force, sometimes the piston rod to bear the transverse load is too large, especially do not force or pull the track steering cylinder, bite. Elimination method: When installing the track steering cylinder, ensure that the axis position of the track steering cylinder is consistent with the direction of movement; Make the load borne by the track steering cylinder as far as possible through the track steering cylinder axis, to avoid the phenomenon of eccentricity.

The track steering cylinder should be avoided for a long time without use, if it is indeed idle for a long time for some reason, it should also be regularly turned on for empty operation, so that its parts can be fully lubricated, so as to avoid rust on the working surface and affect the normal work in the future. (If it cannot be turned on and run, a small amount of lubricating oil can be applied on its outer surface for protection) ' The use of the track steering cylinder should pay attention to: the operation should be as far away from the track steering cylinder as possible, to avoid falling objects, knocking, rubbing the track steering cylinder coating. When cleaning the track steering cylinder, only use soft materials (such as cotton) to wipe, and do not scratch high-hardness materials. Do not use the track steering cylinder when the oil temperature exceeds 70 ° C.

The difference between the plunger track steering cylinder and the piston track steering cylinder is that the piston in the track steering cylinder is replaced by a shaft plunger, which is used in hydraulic transmission requiring a long mechanical stroke, and can only input pressure oil from one direction, pressurize in a single direction, and form a thrust to push the plunger to move. The return trip of the plunger depends on the plunger itself to fall, and some rely on the spring to push back to the original position. Usually used plunger type track steering cylinder, its inner hole does not need mechanical finishing, as long as the plunger round grinding can be assembled.

Improve the service life of the track steering cylinder: it is necessary to maintain the normal clearance of the combined surface of the hydraulic components. When manufacturing or repairing the main parts of the track steering cylinder (such as the track steering cylinder block, piston rod, etc.), the assembly should be carried out in accordance with the tolerance lower limit of the assembly size, which can well reduce the occurrence of cavitation. If cavitation has occurred in the hydraulic components, only metallographic sandpaper polishing technology can be used to remove cavitation pitting and surface carbon deposits, and general fine sandpaper must not be used for polishing After the track steering cylinder is repaired, the hydraulic system should run smoothly for a certain period of time so that the hydraulic oil in the hydraulic system can be fully circulated; If necessary, the track steering cylinder inlet pipe (or return pipe) can be disassembled. Make the hydraulic oil overflow to achieve the effect of single track steering cylinder exhaust.

Answers to some questions about track steering cylinder:

Where is the cylinder used? What is it used for? Can it be used in cars?
Cylinders can be used as actuator in hydraulic system. Such as hydraulic jacks, dump truck box lifting device, dodging (snow) machine loader bucket lifting device. Hydraulic cylinders are also widely used in car cranes. It's all about cars.

100 tons press, the cylinder diameter is 250, how much pressure?
100 tons hydraulic press, if it is a single acting hydraulic cylinder, the required oil pressure is the nominal force divided by the cross-sectional area of the cylinder piston. One hundred tons of its pressure is 1000 kN (1000000N), the diameter of the cylinder is 250 mm, its area is the circular rate multiplied by the square of the radius, is 49062.5 square mm, and then the pressure divided by the area of the oil pressure is 20.38MPa. Therefore, a hydraulic pressure of 20.38 mpa is required for a 250 diameter cylinder to obtain 100 tons of pressure.