steering cylinder Sold to Singapore

This article mainly introduces:

Singapore hydraulic cylinder,steering cylinder manufacturer,steering cylinder

(Singapore steering cylinder,produced by Hebei Hengyu company）

steering cylinder are widely used in Singapore，because of simple structure and reliable operation，excellent temperature resistance，no transmission clearance.So our company has designed steering cylinder for customers from Singapore.

Introduction to steering cylinder:

The internal leakage of the steering cylinder is an important indicator to measure the quality of the steering cylinder: the internal leakage of the steering cylinder will reduce the volumetric efficiency, increase the temperature rise of the oil, affect the positioning accuracy of the steering cylinder, so that the steering cylinder can not accurately and stably stop in a certain position of the steering cylinder, so it is one of the main indicators of the steering cylinder.

What kind of process is used in the steering cylinder to make high-quality steering cylinder products: the body is the main component of the steering cylinder, mining single pillar, hydraulic support, gun tube and other products, and its processing quality directly affects the life and reliability of the entire product. Body processing requirements are high, the internal surface roughness requirements are Ra0.4 ~ 0.8&um, the coaxiality, wear resistance requirements are strict. The basic feature of body is deep hole processing, which has always troubled the processing personnel. The steering cylinder products of our company mainly use rolling processing, because the surface layer has surface residual compressive stress, which helps to close the surface micro-cracks and hinder the expansion of erosion. Thus, the corrosion resistance of the surface can be improved, and the fatigue crack can be delayed or expanded, and the fatigue strength of the body can be improved. The correct rolling process of the steering cylinder block: broaching block - fine boring block - grinding block. The rolling method is: broaching block - fine boring block - rolling block, the process is 3 parts, but the time is compared: grinding 1 meter of the block is about 1-2 days, rolling 1 meter of the block is about 10-30 minutes. Input comparison: grinding machine or quilting machine (tens of thousands - millions), rolling knife (ten thousand - tens of thousands). After rolling, the surface roughness of the hole decreases from RA3.2-6.3um before rolling to RA0.4-0.8&um, the surface hardness of the hole increases by about 30%, and the fatigue strength of the inner surface of the steering cylinder increases by 25%. If the service life of the steering cylinder is only considered, it is increased by 2 to 3 times, and the efficiency of the boring and rolling process is about 3 times higher than that of the grinding process. steering cylinder misoperation or operation failure may be caused by the following reasons, you can start from these aspects of the investigation: (1) spool stuck or valve hole blocked. When the spool of the flow valve or direction valve is stuck or the valve hole is blocked, the steering cylinder is prone to misoperation or operation failure. At this time, the contamination of the oil should be checked; Check whether dirt or colloidal deposits are stuck in the spool or blocking the valve hole; Check the wear of the valve body, clean and replace the system filter, clean the fuel tank, and replace the hydraulic medium. (2) The piston rod and steering cylinder are stuck or the steering cylinder is blocked. At this time, no matter how to manipulate, the steering cylinder does not move or moves very little. At this time, check whether the piston and piston rod seal is too tight, whether it enters the dirt and gum deposits: whether the shaft line of the piston rod and the steering cylinder is in the center, whether the wearing parts and seals are invalid, and whether the load is too large.

The steering cylinder is mainly composed of body, piston, piston rod, steering cylinder head, steering cylinder bottom, piston rod head and related auxiliary devices. The piston divides the steering cylinder into two chambers, and moves reciprocally in the steering cylinder with the help of pressure oil. In order to improve its working effect, there is no sealing ring on the piston to eliminate internal leakage, where the piston rod passes through the steering cylinder head, due to the existence of the gap, it is easy to produce external leakage phenomenon, and the dust can enter the steering cylinder through the gap, so the sealing device and dust prevention reason are set. At the same time, in order to eliminate the influence of eccentric load on the work of the piston, all the steering cylinders must be provided with a considerable length of guide sleeve at the extended end of the piston rod. In addition, in the case of faster piston movement, the phenomenon of mechanical collision between the piston and the steering cylinder bottom and the steering cylinder head is serious, so the buffer deceleration should be set at both ends of the steering cylinder The working medium of the steering cylinder: because it works at room temperature, the ordinary oil-type hydraulic oil can be selected; steering cylinder sealing device: The use of Yx sealing ring, polyurethane (PU) and polytetrafluoroethylene (PTFE) materials combined to achieve a good sealing effect; Buffer mechanism of the steering cylinder: The buffer structure of the steering cylinder is to prevent the piston from colliding with the steering cylinder head at the end of the stroke.

When the control pressure of the hydraulic system is too low, the steering cylinder will appear wrong or no action, because the throttle resistance in the control pipeline may be too large, the flow valve is improperly adjusted, the control pressure is inappropriate, and the pressure source is interfered with. At this time, check the control pressure source to ensure that the pressure is adjusted to the specified value of the system.

Answers to some questions about steering cylinder:

Can multiple identical hydraulic cylinders be supplied with the same supply line?
This can be connected, but there is a disadvantage, that is, the hydraulic cylinder with the minimum pressure is extended first, and then the pressure is higher, and then the higher, until all the hydraulic cylinders are extended, which may not meet the requirements of field use.

How to disassemble injection molding machine injection cylinder?
If it is not repaired for a long time, it is recommended to open both ends, comprehensively check the oil seal and piston ring inside, this is not much difficulty, pay attention to not install reverse when changing the oil seal, some piston rings are steel rings are rubber rings, and several interfaces of steel rings are not in the same position; Rubber ring pay attention not to install reverse; Be careful not to damage the oil seal when installing, otherwise it will soon leak oil.