swager cylinder Sold to Turkmenistan

This article mainly introduces:

Turkmenistan hydraulic cylinder,swager cylinder manufacturer,swager cylinder

(Turkmenistan swager cylinder,produced by Hengyu Hydraulic Cylinder Factory）

swager cylinder are widely used in Turkmenistan，because of excellent fatigue and impact resistance，no need for deceleration device，long service life.So our company has designed swager cylinder for customers from Turkmenistan.

Introduction to swager cylinder:

When the swager cylinder is customized, if there are high requirements for the quality of the swager cylinder, it is best to use rolling processing, because the surface layer has surface residual compressive stress, which helps to close the surface of the small crack, preventing the expansion of erosion. Thus, the corrosion resistance of the surface can be improved, and the fatigue crack can be delayed or expanded, and the fatigue strength of the swager cylinder can be improved. By rolling forming, a cold working hardening layer is formed on the rolling surface, which reduces the elastic and plastic deformation of the contact surface of the grinding pair, thereby improving the wear resistance of the inner wall of the swager cylinder and avoiding the burn caused by grinding. After rolling, the reduction of surface roughness value can improve the matching property.

swager cylinder to reasonable use of hydraulic oil: strict hydraulic oil selection off. Hydraulic oil is selected in strict accordance with oil standards. The selection of good quality hydraulic oil can effectively prevent bubbles in the working process of the hydraulic system. When choosing the oil, it should be selected according to the lowest temperature in different regions, and fill the hydraulic oil according to the dipstick standard, and at the same time, it should also keep the hydraulic system clean (when filling the hydraulic oil, it should prevent the water and other impurities into it), and often check the oil quality, oil level and oil color of the hydraulic oil. If blisters and bubbles are found in the hydraulic oil. When the oil becomes milky white, the source of the air in the oil should be carefully found and eliminated in time.

When the swager cylinder needs to be stored for a period of time, please follow the recommended methods: The swager cylinder should be stored in a dry, clean, non-corrosive gas indoor environment, pay attention to protect the swager cylinder from internal corrosion and external damage. If the indoor requirements cannot be met, the hardened and well-drained ground should be cushioned at least 30cm, and the upper part should be covered with waterproof storage. The oil swager cylinder should not be in direct contact with water vapor for a long time. The swager cylinder should be placed as vertically as possible with the piston rod facing up, which minimizes corrosion due to possible condensation in the swager cylinder and permanent deformation of the seal due to the piston and rod weight. (When the shield is stored in the shield machine, the support shoe is placed upward). Keep the oil port protective cover until the pipe is connected. For long-term storage, the protection should be added on both sides of the piston of the swager cylinder Before working, the swager cylinder must be run repeatedly with low pressure (greater than the starting pressure) to discharge the air in the swager cylinder before normal work. The oil inlet and outlet and the joint must be tightly fastened with a combination pad to prevent oil leakage.

The viscosity of the working oil used in the swager cylinder is 29~74mm2/S, and ISO VG46 anti-wear hydraulic oil is recommended. Working oil temperature within the range of -20~80. C. When the ambient temperature and service temperature are low, the oil with lower viscosity can be selected.

Answers to some questions about swager cylinder:

Does the sealing string of the upper and lower chamber of the hydraulic cylinder fall by itself?
It is possible, the probability accounts for 85% (depending on the weight), the weight is less than the system resistance, may not fall, the weight is greater than the system resistance, will not necessarily fall, so often check the equipment, safety first, find the problem in time to solve, the cylinder is not very expensive parts, maintenance does not cost much money, However, accidents caused by cylinder failure will lose several times the cost.

Why the lifting cylinder falling by itself?
May be there is a pressure relief point. Check and repair the following parts: whether there is oil leakage in the transparent pipe at the top of the cylinder: the cylinder oil seal is broken, and the cylinder and oil seal need to be replaced; No: The multiway valve has pressure relief and needs to be repaired. Maintenance in accordance with routine maintenance items can reduce mechanical failures: 1. Check whether the thermostat works normally. 2, check the transmission shift work is normal. 3. Check the tightness of the fan belt. 4, check whether the diesel tank oil inlet filter is blocked or damaged, and clean or replace the filter. 5. Check and adjust the valve clearance.