sanitation truck hydraulic cylinder Sold to Holland

This article mainly introduces:

Holland hydraulic cylinder,sanitation truck hydraulic cylinder manufacturer,sanitation truck hydraulic cylinder

(Holland sanitation truck hydraulic cylinder,produced by Hebei Hengyu company）

sanitation truck hydraulic cylinder are widely used in Holland，because of clever hydraulic energy conversion，simple structure and reliable operation，excellent temperature resistance.So our company has designed sanitation truck hydraulic cylinder for customers from Holland.

Introduction to sanitation truck hydraulic cylinder:

What kind of process is used in the sanitation truck hydraulic cylinder to make high-quality sanitation truck hydraulic cylinder products: the body is the main component of the sanitation truck hydraulic cylinder, mining single pillar, hydraulic support, gun tube and other products, and its processing quality directly affects the life and reliability of the entire product. Body processing requirements are high, the internal surface roughness requirements are Ra0.4 ~ 0.8&um, the coaxiality, wear resistance requirements are strict. The basic feature of body is deep hole processing, which has always troubled the processing personnel. The sanitation truck hydraulic cylinder products of our company mainly use rolling processing, because the surface layer has surface residual compressive stress, which helps to close the surface micro-cracks and hinder the expansion of erosion. Thus, the corrosion resistance of the surface can be improved, and the fatigue crack can be delayed or expanded, and the fatigue strength of the body can be improved. The correct rolling process of the sanitation truck hydraulic cylinder block: broaching block - fine boring block - grinding block. The rolling method is: broaching block - fine boring block - rolling block, the process is 3 parts, but the time is compared: grinding 1 meter of the block is about 1-2 days, rolling 1 meter of the block is about 10-30 minutes. Input comparison: grinding machine or quilting machine (tens of thousands - millions), rolling knife (ten thousand - tens of thousands). After rolling, the surface roughness of the hole decreases from RA3.2-6.3um before rolling to RA0.4-0.8&um, the surface hardness of the hole increases by about 30%, and the fatigue strength of the inner surface of the sanitation truck hydraulic cylinder increases by 25%. If the service life of the sanitation truck hydraulic cylinder is only considered, it is increased by 2 to 3 times, and the efficiency of the boring and rolling process is about 3 times higher than that of the grinding process. sanitation truck hydraulic cylinder misoperation or operation failure may be caused by the following reasons, you can start from these aspects of the investigation: (1) spool stuck or valve hole blocked. When the spool of the flow valve or direction valve is stuck or the valve hole is blocked, the sanitation truck hydraulic cylinder is prone to misoperation or operation failure. At this time, the contamination of the oil should be checked; Check whether dirt or colloidal deposits are stuck in the spool or blocking the valve hole; Check the wear of the valve body, clean and replace the system filter, clean the fuel tank, and replace the hydraulic medium. (2) The piston rod and sanitation truck hydraulic cylinder are stuck or the sanitation truck hydraulic cylinder is blocked. At this time, no matter how to manipulate, the sanitation truck hydraulic cylinder does not move or moves very little. At this time, check whether the piston and piston rod seal is too tight, whether it enters the dirt and gum deposits: whether the shaft line of the piston rod and the sanitation truck hydraulic cylinder is in the center, whether the wearing parts and seals are invalid, and whether the load is too large.

When the sanitation truck hydraulic cylinder is installed, it is necessary to ensure that the direction of the connecting head at the top of the piston rod should be consistent with the direction of the sanitation truck hydraulic cylinder head, earring (or middle hinge shaft), and ensure the straightness of the whole piston rod during the advance and return process to prevent rigid interference and cause unnecessary damage.

Protection of the sanitation truck hydraulic cylinder surface: During the dismantling process, safety protection should be carried out on the sanitation truck hydraulic cylinder to prevent objects from falling and welding slag from falling to the surface, causing damage to the sanitation truck hydraulic cylinder surface. In the process of propulsion, the damaged pipe segments should be prevented from falling and smashing, and the slurry remaining on the surface of the sanitation truck hydraulic cylinder should be cleaned up in time.

The viscosity of the working oil used in the sanitation truck hydraulic cylinder is 29~74mm2/S, and ISO VG46 anti-wear hydraulic oil is recommended. Working oil temperature within the range of -20~80. C. When the ambient temperature and service temperature are low, the oil with lower viscosity can be selected.

Answers to some questions about sanitation truck hydraulic cylinder:

Why are two cylinders not balanced with the balance valve?
Balancing valve is only suitable for occasions with low synchronous accuracy requirements, and proportional valves are recommended for occasions with high precision requirements.

Where's the hydraulic cylinder bleed valve?
There is a vent hole at the top of the cylinder next to the intake pipe. Generally, it can be used, and the air in the cylinder can be naturally drained after several moves.