self-locking hydraulic cylinder Sold to Kuwait

This article mainly introduces:

Kuwait hydraulic cylinder,self-locking hydraulic cylinder manufacturer,self-locking hydraulic cylinder

(Kuwait self-locking hydraulic cylinder,produced by Hengyu Group）

self-locking hydraulic cylinder are widely used in Kuwait，because of powerful torque，clever hydraulic energy conversion，simple structure and reliable operation.So our company has designed self-locking hydraulic cylinder for customers from Kuwait.

Introduction to self-locking hydraulic cylinder:

1, the hydraulic machinery should be kept clean, in order to prevent dust and debris from falling into the oil, the tank should be sealed. 2, the oil in the tank should be replaced regularly according to the working condition. When changing the oil, the dirt and impurities accumulated at the bottom of the tank should be removed and the tank should be cleaned. 3, hydraulic oil, oil drums should be set in a clean and safe place to strengthen management. The oil drum, oil filter, oil funnel, oil pipe, etc. used should be kept clean. The oil drums for loading hydraulic oil must be cleaned in advance, and the oil drums should be dedicated and not mixed with other oil drums.

How the cavitation of the self-locking hydraulic cylinder is formed: With the gradual rise of pressure, the gas in the oil will become bubbles, when the pressure rises to a certain limit value, these bubbles will break under the action of high pressure, so that the high temperature and high pressure gas will quickly act on the surface of the parts, resulting in cavitation of the self-locking hydraulic cylinder, resulting in corrosive damage to the parts.

When the self-locking hydraulic cylinder thrust is insufficient, check the hydraulic circuit for leaks. Including leakage of valves and hydraulic lines. The inspection method is to check and eliminate the leakage of the hydraulic connection line by manipulating the reversing valve. Also consider the relief valve. If the relief valve enters the dirt and jams the spool, so that the relief valve is normally open, the hydraulic oil will flow directly back to the tank through the relief valve bypass, resulting in no oil in the self-locking hydraulic cylinder. If the load is too large, although the regulating pressure of the relief valve has reached the maximum rating, the self-locking hydraulic cylinder still cannot get the thrust required for continuous action without action. If the regulating pressure is low, the pressure is insufficient to achieve the required vertebra force, which is manifested as insufficient thrust. Check and adjust the relief valve at this time.

self-locking hydraulic cylinder and hydraulic station selection: Select the type and structure of the self-locking hydraulic cylinder according to the operation requirements of the main engine. According to the external load force borne by the self-locking hydraulic cylinder, such as gravity, friction force of the external mechanism, inertia force and working load, determine the load change law of the self-locking hydraulic cylinder in each stage of the stroke and the power value that must be provided. Determine the diameter of the piston and piston rod according to the working load of the self-locking hydraulic cylinder and the selected oil working pressure. the flow rate of the hydraulic pump is determined according to the movement speed of the self-locking hydraulic cylinder, the diameter of the piston and the piston rod.

Answers to some questions about self-locking hydraulic cylinder:

Servo cylinder control principle
The electro-hydraulic pulse servo cylinder is composed of a stepper motor, a three-position four-way servo valve, a mechanical feedback device (a wire carrier) and an oil lever. When the stepper motor gets a pulse signal, its output shaft rotates 1.5 or 3 degrees, the servo valve spool drives the wire to rotate at the same time, the valve spool moves and opens the reversing cylinder to output pressure oil, the piston moves and drives the lead screw to reverse rotate the valve spool back to the original position, and the servo valve stops output pressure oil in the center. At this time, the cylinder moves 0.1 or 0.2mm stroke, and the displacement and speed of the cylinder travel are determined according to the given value of the electrical pulse.

Why is the hydraulic cylinder of the larger excavator arm upside down?
The weight of the excavating arm of a large excavator will be very heavy, and an oil cylinder has two cavities, one is a rod cavity, and the other is a rodless cavity. The lifting force of the excavator is the product of the ortho-projection area of the piston rod cavity by the oil pressure, so the strength of the rodless cavity is much greater than that of the rod cavity. And the parallel bars with the piston rod facing down are also conducive to assembly and future maintenance. So a large excavator has to keep the cylinder facing down.