yg series hydraulic cylinder Sold to Thailand

This article mainly introduces:

Thailand hydraulic cylinder,yg series hydraulic cylinder manufacturer,yg series hydraulic cylinder

(Thailand yg series hydraulic cylinder,produced by Hengyu Group）

yg series hydraulic cylinder are widely used in Thailand，because of simple structure and reliable operation，excellent temperature resistance，no transmission clearance.So our company has designed yg series hydraulic cylinder for customers from Thailand.

Introduction to yg series hydraulic cylinder:

When the yg series hydraulic cylinder needs to be stored for a period of time, please follow the recommended methods: The yg series hydraulic cylinder should be stored in a dry, clean, non-corrosive gas indoor environment, pay attention to protect the yg series hydraulic cylinder from internal corrosion and external damage. If the indoor requirements cannot be met, the hardened and well-drained ground should be cushioned at least 30cm, and the upper part should be covered with waterproof storage. The oil yg series hydraulic cylinder should not be in direct contact with water vapor for a long time. The yg series hydraulic cylinder should be placed as vertically as possible with the piston rod facing up, which minimizes corrosion due to possible condensation in the yg series hydraulic cylinder and permanent deformation of the seal due to the piston and rod weight. (When the shield is stored in the shield machine, the support shoe is placed upward). Keep the oil port protective cover until the pipe is connected. For long-term storage, the protection should be added on both sides of the piston of the yg series hydraulic cylinder Before working, the yg series hydraulic cylinder must be run repeatedly with low pressure (greater than the starting pressure) to discharge the air in the yg series hydraulic cylinder before normal work. The oil inlet and outlet and the joint must be tightly fastened with a combination pad to prevent oil leakage.

How to determine the working pressure of the yg series hydraulic cylinder: The pressure depends on the load size (i.e., F) and the type of equipment. The limitations of assembly space, economic conditions and component availability of the actuator should also be considered. In the case of a certain load, it is necessary to increase the structural size of the actuator if the working pressure is low, for some equipment, the size may be limited, and it is not economical from the point of view of material consumption; On the contrary, if the pressure selection is too high, the material, sealing and manufacturing accuracy of the pump, yg series hydraulic cylinder, valve and other components are also required to be high, which will inevitably increase the cost of equipment. In general, for equipment with a fixed size that is not too limited, the pressure can be selected lower, and the walking machinery should be selected higher.

The commonly used buffer structure of the yg series hydraulic cylinder is composed of a piston boss and a yg series hydraulic cylinder head groove. When the piston moves close to the yg series hydraulic cylinder head, it gradually enters the groove, and the oil in the groove is extruded through the gap between the boss and the groove, which increases the oil return resistance, produces the braking effect and realizes the buffer. Generally, a buffer mechanism should be used when the pressure is above 10MP.

yg series hydraulic cylinder hydraulic oil selection: The recommended working oil viscosity of the yg series hydraulic cylinder is 10 ~ 110cSt (1.8 ~ 15E), ISO VG46 hydraulic oil. The normal working oil temperature is 10 ~ 70℃, and the ambient temperature is in the range of -20 ~ 80℃. When the ambient temperature and service temperature are low, the hydraulic oil with lower viscosity can be selected.

Answers to some questions about yg series hydraulic cylinder:

How to calculate the cylinder diameter, rod diameter and pressure of the cylinder, and how to output tonnage?
Hydraulic cylinder output force F=PAX10^3(KN) F is the output force (KN), P working pressure (MPa), A is the piston or plunger area of action.

What are the causes of hydraulic cylinder oil leakage?
First, between the piston rod and the guide sleeve: 1, the cylinder force is not good, there is a radial force between the piston rod and the guide sleeve there is a partial load, so that the oil seal is worn early, causing oil leakage. 2. The ambient temperature of the piston rod is high, especially radiant heat, and the oil seal aging is fast. 3. Whether the oil seal is selected correctly; Check whether the oil seal is damaged during installation. 4, guide sleeve and piston rod matching tolerance is correct. Second, between guide sleeve and cylinder: 1. Whether the O-ring on the guide sleeve is installed correctly, pay special attention to the O-ring can not "roll", especially some O-rings are die-pressed with a die-closing line. Third, common problems: 1, guide sleeve, cylinder, piston rod concentricity is poor. Fit tolerance is correct.