boarding axle cylinder Sold to Ghana

This article mainly introduces:

Ghana hydraulic cylinder,boarding axle cylinder manufacturer,boarding axle cylinder

(Ghana boarding axle cylinder,produced by Hengyu Group）

boarding axle cylinder are widely used in Ghana，because of no transmission clearance，powerful torque，clever hydraulic energy conversion.So our company has designed boarding axle cylinder for customers from Ghana.

Introduction to boarding axle cylinder:

The piston seal of the boarding axle cylinder is the main element to prevent leakage in the boarding axle cylinder. For the lip seal, it should focus on checking whether the lip edge is bruised and worn, and for the combination seal, it should focus on checking the wear of the sealing surface, and then determine whether the seal can be used. In addition, it is necessary to check whether the static seal between the piston and the piston rod is crushed. The piston rod seal should focus on checking the wear of the seals and supporting rings.

At the rated pressure, the thrust of the boarding axle cylinder is determined by what factors: at the rated pressure of the oil pump, the work done by the boarding axle cylinder is related to the diameter of the boarding axle cylinder, but not to the stroke of the boarding axle cylinder. Moreover, the larger the boarding axle cylinder diameter, the larger the area, and the greater the pressure obtained. To this point, we should have a correct understanding and clear understanding, so as to avoid problems in the use of the boarding axle cylinder.

The oil boarding axle cylinder is a part of the hydraulic system, in the hydraulic system, to reasonably design the heat dissipation system, to prevent the oil temperature is too high is the key to keep the hydraulic oil temperature normal. The temperature of the system should be kept in a suitable range to reduce the energy released when the bubble bursts. While not affecting the normal circulation of the coolant, a certain amount of anti-corrosion additives can be appropriately added to inhibit rust. When operating the hydraulic system, we should strive to be stable, not too fast, too strong, and try to reduce the impact of hydraulic oil on hydraulic components.

If the boarding axle cylinder operation failure, you can start from these aspects to troubleshoot: (1) the hydraulic system control pressure is too low. The throttling resistance in the control line may be too large, the flow valve is improperly adjusted, the control pressure is inappropriate, and the pressure source is disturbed. At this time, the control pressure source should be checked to ensure that the pressure is adjusted to the specified value of the system; (2) Air enters the hydraulic system. Mainly because there is a leak in the system. At this time, check the liquid level of the hydraulic tank, the seals and fittings on the oil suction side of the hydraulic pump, and whether the oil suction filter is too dirty. If so, the hydraulic oil should be replenished, seals and fittings should be treated, and the coarse filter element should be cleaned or replaced. (3) The initial action of the boarding axle cylinder is slow. In the case of low temperature, the hydraulic oil viscosity is large, poor flow, resulting in slow boarding axle cylinder action. The improvement method is to replace the hydraulic oil with better viscosity and temperature performance If the boarding axle cylinder is weak and cannot push the load, please check the internal leakage problem. The internal leakage of the boarding axle cylinder includes the leakage caused by excessive wear of the boarding axle cylinder block seal, the piston rod and the seal cover seal and the piston seal. The cause of sealing leakage between the piston rod and the seal cover is that the seal is wrinkled, squeezed, torn, worn, aging, deterioration, deformation, etc., and a new seal should be replaced at this time. The main cause of excessive piston seal wear is improper adjustment of the speed control valve, resulting in excessive back pressure and improper seal installation or hydraulic oil contamination. The second is that foreign bodies enter the assembly and the quality of sealing materials is not good. The result is that the action is slow and weak, and in serious cases, it will cause damage to the piston and boarding axle cylinder, and the phenomenon of "pulling the boarding axle cylinder" appears. The treatment method is to adjust the speed control valve, and the necessary operations should be done according to the installation instructions.

Answers to some questions about boarding axle cylinder:

What are the reasons why the hydraulic cylinder action is slower than normal?
There are many factors that cause this problem. First, measure the pressure of the main system to see whether the pressure of the main system under the pressure state is consistent with the initial setting. Before measuring the pressure, it is best to check the hydraulic oil and suction oil filter and replace or clean it. Second, check the main relief valve of the reversing control multiway valve to see if there is damage or foreign matter blocking, and clean it. If your pump is a gear pump, the problem should generally be small. Second, look at traffic. There is no leakage in the cylinder, leakage in the reversing valve spool and so on.

What does the maximum output force of the cylinder piston mean?
The maximum output of the cylinder is related to the pressure of the hydraulic system that you link to the cylinder. For example, the rated maximum output thrust of the MOB 50 cylinder is 1.3 tons and the rated pressure is 7Mpa. That is, when the input hydraulic oil pressure of the cylinder reaches 7Mpa, the maximum output thrust of the cylinder is only 0.98 tons. When the input hydraulic pressure is only 5Mpa, the maximum output thrust of the cylinder is 1.3 tons. Because the pressure of the cylinder limit is only 7Mpa, if the oil pressure of the input system exceeds 7Mpa, the cylinder can not withstand the pressure burst, and it is damaged.